Toyota Sienna Disc Brake Caliper Replacement

2004-2010 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-59491L

For 4-door van models.

Condition: Excellent (A)
Mileage: 239,000 miles

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 12s-a L, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.685, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.44601

$57.42 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 12s-a L, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.685, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2873

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$57.26 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B2872

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$59.29 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 4 L, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 2.494, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$62.49 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2694

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$61.29 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 4 L, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 2.37, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44235

$63.90 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2076

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$61.70 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01628B

Supplied w/ Mounting Bracket

$64.55 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 40, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Aluminum, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.59, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1998-2000 Toyota Sienna Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44192

$61.83 View part →

2013-2020 Toyota Sienna Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B7080

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$69.67 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44144

$61.92 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P01628B

Supplied w/ Mounting Bracket

$70.63 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44236

$63.90 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01664B

Supplied w/ Mounting Bracket

$70.89 View part →

2012-2020 Toyota Sienna Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.44664

$64.49 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01661B

Supplied w/ Mounting Bracket

$71.84 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-01628A

Supplied w/ Mounting Bracket

$64.55 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01665A

Supplied w/ Mounting Bracket

$72.19 View part →

2011 Toyota Sienna Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.44642

$66.40 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01665A

Supplied w/ Mounting Bracket

$74.10 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P01628A

Supplied w/ Mounting Bracket

$70.63 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P01661B

Supplied w/ Mounting Bracket

$77.60 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-01664A

Supplied w/ Mounting Bracket

$70.89 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC12481

$79.01 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-01661A

Supplied w/ Mounting Bracket

$71.84 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (Centric)

Partslink #: 142.44235

$82.55 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01665B

Supplied w/ Mounting Bracket

$72.19 View part →

2011 Toyota Sienna Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.44641

$84.84 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 1115, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.748, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01665B

Supplied w/ Mounting Bracket

$74.10 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B6275

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$86.24 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P01661A

Supplied w/ Mounting Bracket

$77.60 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P01718B

Supplied w/ Mounting Bracket

$88.31 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-59050L

Condition: Excellent (A)
Mileage: 327,000 miles

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3362954

$94.41 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44282

$83.02 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01718B

Supplied w/ Mounting Bracket

$95.45 View part →

2015-2019 Toyota Sienna Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01738B

Supplied w/ Mounting Bracket SUPERSEDE

$85.68 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 1116, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.748, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-76676

$95.99 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B6274

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$85.96 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 1116, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.332, Mounting Hole Thread Diameter: 0.332, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.748, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01719A

Supplied w/ Mounting Bracket

$96.43 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-6274

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$88.06 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC11659N

$96.53 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P01718A

Supplied w/ Mounting Bracket

$88.31 View part →

2012-2020 Toyota Sienna Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-76714

$97.05 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3391973

$95.15 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2872

$97.42 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-01718A

Supplied w/ Mounting Bracket

$95.45 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3398652

$97.70 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-76677

$95.99 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L15092

$98.88 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01719B

Supplied w/ Mounting Bracket

$96.43 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01719A

Supplied w/ Mounting Bracket

$99.22 View part →

2012-2020 Toyota Sienna Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-76715

$97.05 View part →

2011 Toyota Sienna Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-76702

$102.19 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2873

$97.42 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3458605

$110.93 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3339148

$97.70 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3385311

Production: 01/01/2010-09/30/2011

$119.68 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L15093

$98.88 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L6275

$119.94 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01719B

Supplied w/ Mounting Bracket

$99.22 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2715

$123.49 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3374230

$110.93 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76204

$123.85 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (CARQUEST)

Partslink #: W0133-1919532

$119.13 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2076

$133.95 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.69, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2714

$123.49 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 2C-2872

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$136.04 View part →

2004-2010 Toyota Sienna Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76205

$123.85 View part →

2021-2025 Toyota Sienna Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-10998R

For vehicles with the 2.5L engine, continuously variable transmission (CVT), and front-wheel drive.

Condition: Excellent (A)
Mileage: 131,000 miles

$139.95 View part →

1998-2000 Toyota Sienna Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2077

$133.95 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76234

$149.09 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L6274

$135.05 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.69, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3503736

Production: 01/01/2010-

$154.83 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.75, Piston Material: Steel, Piston Quantity: 2, Product Condition: New, Rust Resistant Coating: Yes

2004-2010 Toyota Sienna Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 2C-2873

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$136.04 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Right (Cardone)

Partslink #: 2C-6275

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$195.57 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3358896

Production: 01/01/2010-09/30/2011

$139.58 View part →

2021-2025 Toyota Sienna Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-10999L

It is compatible with front-wheel drive vehicles equipped with a 2.5L engine and a continuously variable transmission.

Condition: Excellent (A)
Mileage: 131,000 miles

$139.95 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76235

$149.09 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3370864

Production: 01/01/2010-

$154.83 View part →

2001-2003 Toyota Sienna Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76137

$162.32 View part →

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50666R

For 4-door van models.

Condition: Excellent (A)
Mileage: 166,000 miles

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It was removed from a 4-door van.

Condition: Excellent (A)

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50666R

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 113,000 miles

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 76,000 miles

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50666R

It was removed from a 4-door van.

Condition: Excellent (A)

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 113,000 miles

2004-2010 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-59490R

For 4-door van models.

Condition: Excellent (A)
Mileage: 239,000 miles

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 166,000 miles

2021-2025 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-10996

For vehicles with All-Wheel Drive (AWD) and the 2.5L engine. This brake caliper is silver.

Condition: Excellent (A)
Mileage: 19,000 miles

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-50669

For all-wheel drive (AWD) vehicles with the 2.5L engine. This part has gray connectors.

Condition: Excellent (A)
Mileage: 34,000 miles

2011-2020 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50666

For all-wheel drive vehicles with the 2.5L engine. This part features a gray finish.

Condition: Excellent (A)
Mileage: 34,000 miles

2021-2025 Toyota Sienna Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-10997

The part itself is silver.

Condition: Excellent (A)
Mileage: 19,000 miles

2021-2025 Toyota Sienna Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-10996R

It is compatible with front-wheel drive vehicles equipped with a 2.5L engine and a continuously variable transmission.

Condition: Excellent (A)
Mileage: 131,000 miles

$83.95 View part →