Toyota 4Runner Disc Brake Caliper Replacement

1986-1989 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01513B

To 03/89

$49.02 View part →

1991-1996 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01560A

To 10/95

$49.96 View part →

1991-1996 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01560B

To 10/95

$49.96 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: S12+8, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.48, Mounting Hole Thread Diameter: 0.48, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.683, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1984-1985 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01512A

$53.82 View part →

1984-1985 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-821

Installation Hardware Included with Metal Piston

$51.44 View part →

1988-1991 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01550A

To 06/91

$54.29 View part →

1984-1985 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01512B

$53.82 View part →

1991-1996 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01560A

To 10/95

$55.54 View part →

1988-1991 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01550B

To 06/91

$54.29 View part →

1988-1991 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01550A

To 06/91

$56.83 View part →

1991-1996 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01560B

To 10/95

$55.54 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01662A

Supplied w/ Mounting Bracket

$69.12 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: FRC11556

$57.15 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01662A

Supplied w/ Mounting Bracket

$71.21 View part →

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$58.52 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 14b-l, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.785, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1986-1989 Toyota 4Runner Disc Brake Caliper - Front Right (Raybestos)

Partslink #: RC3189

with Vented Rotors 4 Piston Caliper

$72.76 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: No, Caliper Type: Fixed, Casting Number: S12we, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.48, Mounting Hole Thread Diameter: 0.48, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.684, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2727

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$58.65 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: S13wb, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.481, Mounting Hole Thread Diameter: 0.481, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-1829

Installation Hardware Included with 15 (in) Wheels with Metal Piston

$73.05 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13wg, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.465, Mounting Hole Thread Diameter: 0.465, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1991-1995 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-1601

From 06/1991 Installation Hardware Included with Metal Piston

$61.38 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-2984

Casting # 13WG Installation Hardware Included with Metal Piston

$73.24 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01662B

Supplied w/ Mounting Bracket

$69.12 View part →

1995-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44179

Fr 11/95 Caliper Casting# S12WE 297mm Front Disc

$73.97 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13wh, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.48, Mounting Hole Thread Diameter: 0.48, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01662B

Supplied w/ Mounting Bracket

$71.21 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-2766

Casting # 13WH Installation Hardware Included with Metal Piston

$74.24 View part →

1992-1995 Toyota 4Runner Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC10376

Replaces RWC50169

$72.04 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: No, Caliper Type: Fixed, Casting Number: S 13 Wm, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.481, Mounting Hole Thread Diameter: 0.481, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.785, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44227

338mm Front Disc Front Caliper Casting# 13WH

$75.18 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: No, Caliper Type: Fixed, Casting Number: S13wm, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.481, Mounting Hole Thread Diameter: 0.481, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.785, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-1830

Installation Hardware Included with 16 (in) Wheels with Metal Piston

$73.29 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-1831

Installation Hardware Included with 16 (in) Wheels with Metal Piston

$75.44 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44228

338mm Front Disc Front Caliper Casting# 13WH

$75.18 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13wh, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.48, Mounting Hole Thread Diameter: 0.48, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1995-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44177

Fr 11/95 Caliper Casting# S13WM 319mm Front Disc

$75.74 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-2767

Casting # 13WH Installation Hardware Included with Metal Piston

$76.77 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01653A

Supplied w/ Mounting Bracket

$77.75 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01653B

Supplied w/ Mounting Bracket

$77.75 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13wl, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.477, Mounting Hole Thread Diameter: 0.477, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44245

319mm Front Disc Front Caliper Casting# 13WG

$78.52 View part →

2003-2005 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-2713

Casting # 13WL Installation Hardware Included with Metal Piston

$79.54 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01652A

w/ 17" Wheel, Casting No 13WH

$82.15 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01652B

w/ 17" Wheel, Casting No 13WH

$82.15 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 14 Wa, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.477, Mounting Hole Thread Diameter: 0.477, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.892, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01596B

w/ 15" Wheel

$82.83 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-6279

Installation Hardware Included with Metal Piston

$82.67 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC10792C

w/ Front Caliper Casting # S13WM 16" Wheels Casting # 13WM

$83.13 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01596A

w/ 15" Wheel

$82.83 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01653A

Supplied w/ Mounting Bracket

$83.53 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 14 Wa, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.477, Mounting Hole Thread Diameter: 0.477, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.892, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC10791C

w/ Front Caliper Casting # S13WM 16" Wheels Casting # 13WM

$83.13 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-6278

Installation Hardware Included with Metal Piston

$83.81 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01653B

Supplied w/ Mounting Bracket

$83.53 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01645A

w/ 16" Wheel, Casting No 13WG

$85.40 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01645B

w/ 16" Wheel, Casting No 13WG

$85.40 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC10792

w/ Front Caliper Casting # S13WM 16" Wheels Casting # 13WM

$85.58 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01645B

w/ 16" Wheel, Casting No 13WG

$85.59 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01645A

w/ 16" Wheel, Casting No 13WG

$85.59 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01652B

w/ 17" Wheel, Casting No 13WH

$86.20 View part →

2003-2004 Toyota 4Runner Disc Brake Caliper - Front Left or Front Right (BBB Industries)

Partslink #: 97-01651B

w/ 16" Wheel, Casting No 13WL

$85.77 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01597A

w/ 16" Wheel

$86.49 View part →

2003-2004 Toyota 4Runner Disc Brake Caliper - Front Left or Front Right (BBB Industries)

Partslink #: 97-01651A

w/ 16" Wheel, Casting No 13WL

$85.77 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01596A

w/ 15" Wheel

$87.53 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01652A

w/ 17" Wheel, Casting No 13WH

$86.20 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01725B

$88.51 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01597B

w/ 16" Wheel

$86.49 View part →

2003-2004 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01651B

w/ 16" Wheel, Casting No 13WL

$90.49 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC11553C

w/ Casting # 13WG

$87.25 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2727

$91.23 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01596B

w/ 15" Wheel

$87.53 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01725B

$93.18 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01725A

$88.51 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (ACDelco)

Partslink #: 18FR1421

$93.31 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC12551C

$89.84 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Centric)

Partslink #: 142.44228

338mm Front Disc Front Caliper Casting# 13WH

$93.42 View part →

2003-2004 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01651A

w/ 16" Wheel, Casting No 13WL

$90.49 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01597A

w/ 16" Wheel

$94.23 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2736

$91.71 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-76615

$99.22 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01725A

$93.18 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2737

$101.68 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01597B

w/ 16" Wheel

$94.23 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01756B

$115.24 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC10463N

$95.09 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01756B

$119.68 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-76614

$99.22 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3428593

Production: 08/01/2002-, w/ Casting Number 13WH

$125.60 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Powder Coated, Caliper Slides Included: No, Caliper Type: Fixed, Casting Number: 14wb, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: No, Mounting Hole Diameter: 0.557, Mounting Hole Thread Diameter: 0.557, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.89, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2726

$101.09 View part →

2015-2023 Toyota 4Runner Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-7283

Installation Hardware Included with Metal Piston

$126.20 View part →

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-76666

$103.51 View part →

2014-2023 Toyota 4Runner Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44306

14mm Mount

$131.10 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01756A

$115.24 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3379252

$131.81 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01756A

$119.68 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3498161

Production: 08/01/2009-

$133.89 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3448052

Production: 08/01/2002-

$124.88 View part →

1984-1985 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76011

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3358064

Production: 08/01/2002-, w/ Casting Number 13WH

$125.60 View part →

1986-1988 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76013

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Powder Coated, Caliper Slides Included: No, Caliper Type: Fixed, Casting Number: 14wb, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: No, Mounting Hole Diameter: 0.557, Mounting Hole Thread Diameter: 0.557, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.89, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2015-2023 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-7282

Installation Hardware Included with Metal Piston

$127.88 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L15020

From 6/15/2015

$143.17 View part →

2014-2023 Toyota 4Runner Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44305

14mm Mount

$131.10 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76197

338mm Front Disc Front Caliper Casting No 13WH

$143.34 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3508426

$131.81 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76213

319mm Front Disc Front Caliper Casting No 13WG

$146.51 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3431916

Production: 08/01/2009-

$135.21 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3337057

w/ Casting number 13WG or 13WZ

$146.79 View part →

1984-1985 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76010

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2985

with 319mm Front Rotor

$147.85 View part →

1986-1988 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76012

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L1830

with 319mm Front Rotor

$147.95 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L15021

From 6/15/2015

$143.17 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76239

To 05/2015 M12 Mounting Holes

$150.12 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76196

338mm Front Disc Front Caliper Casting No 13WH

$143.34 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2767

with 338mm Front Rotor

$154.18 View part →

1995-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L1828

Mfg from 8/1995 with 297mm (11.69") Front Rotors

$144.26 View part →

1992-1995 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76151

$155.19 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76212

319mm Front Disc Front Caliper Casting No 13WG

$146.51 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L6279

$155.79 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2984

with 319mm Front Rotor

$147.85 View part →

1995-2002 Toyota 4Runner Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L1829

Mfg from 8/1995 with 297mm (11.69") Front Rotors

$157.25 View part →

1996-2002 Toyota 4Runner Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L1831

with 319mm Front Rotor

$147.95 View part →

2016-2023 Toyota 4Runner Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-4123111

$159.63 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3421813

w/ Casting number 13WG or 13WZ

$149.71 View part →

2016-2024 Toyota 4Runner Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76255

From 06/2015 M14 Mounting Holes

$166.04 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76238

To 05/2015 M12 Mounting Holes

$150.12 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Rear Left (Advics)

Partslink #: W0133-1741023

$275.70 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2766

with 338mm Front Rotor

$154.18 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Front Left (Advics)

Partslink #: W0133-2160575

Production: 08/01/2009-

$299.78 View part →

1992-1995 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76150

$155.19 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Left (Advics)

Partslink #: W0133-1742402

Production: 08/01/2002-

$338.46 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L6278

$155.79 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Left (Advics)

Partslink #: W0133-5199651

w/ Casting number 13WG or 13WZ

$426.42 View part →

2016-2023 Toyota 4Runner Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-4123139

$159.63 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: No, Caliper Type: Fixed, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.481, Mounting Hole Thread Diameter: 0.481, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.68, Piston Material: Steel, Piston Quantity: 4, Product Condition: New, Rust Resistant Coating: Yes

2016-2024 Toyota 4Runner Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76254

From 06/2015 M14 Mounting Holes

$166.04 View part →

1988-1991 Toyota 4Runner Disc Brake Caliper - Front Right (Cardone)

Partslink #: 2C-1240

Installation Hardware Included with Metal Piston Obsolete

$167.58 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Rear Right (Advics)

Partslink #: W0133-1741026

$232.41 View part →

2010-2023 Toyota 4Runner Disc Brake Caliper - Front Right (Advics)

Partslink #: W0133-2160464

Production: 08/01/2009-

$272.70 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Advics)

Partslink #: W0133-5199634

w/ Casting number 13WG or 13WZ

$326.54 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Rear Right (Advics)

Partslink #: W0133-1742403

Production: 08/01/2002-

$338.46 View part →

2003-2009 Toyota 4Runner Disc Brake Caliper - Front Right (Advics)

Partslink #: W0133-4530399

Production: 08/01/2002-, w/ Casting Number 13WH

$442.55 View part →

2015-2024 Toyota 4Runner Front Disc Brake Caliper - Right (Passenger) (Used OEM)

Partslink #: 536-61823R

Condition: Excellent (A)
Mileage: 33,600 miles

1996-2002 Toyota 4Runner Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-61101L

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 184,000 miles

$55.95 View part →

1988-1991 Toyota 4Runner Front Disc Brake Caliper - Right (Passenger) (Used OEM)

Partslink #: 536-58259R

Condition: Excellent (A)
Mileage: 121,000 miles

Sale price: $109.95

$91.95 View part →

2003-2009 Toyota 4Runner Front Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-59447L

Condition: Excellent (A)
Mileage: 163,900 miles

$88.95 View part →

2015-2024 Toyota 4Runner Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-61823

Condition: Excellent (A)
Mileage: 71,000 miles

$159.95 View part →

2003-2009 Toyota 4Runner Front Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-59446L

Condition: Excellent (A)
Mileage: 130,000 miles

2025 Toyota 4Runner Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-11787

Condition: Excellent (A)
Mileage: 2,000 miles

$169.95 View part →

2010-2015 Toyota 4Runner Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-51012L

Condition: Excellent (A)
Mileage: 124,000 miles

$149.95 View part →

2025 Toyota 4Runner Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-11787

Condition: Excellent (A)
Mileage: 1,000 miles

$203.95 View part →

2025-2026 Toyota 4Runner Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-11788

Condition: Excellent (A)
Mileage: 12,000 miles

$159.95 View part →

2025-2026 Toyota 4Runner Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-11790

For vehicles with a 1-cylinder brake caliper.

Condition: Excellent (A)
Mileage: 2,000 miles

$169.95 View part →

1996-2002 Toyota 4Runner 4-Piston Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-61100R

For 4-door SUV models.

Condition: Excellent (A)
Mileage: 184,000 miles

$55.95 View part →

2015-2024 Toyota 4Runner Front 4-Piston Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-61824L

Condition: Excellent (A)
Mileage: 33,600 miles

2015-2024 Toyota 4Runner Front 4-Piston Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-61824L

Condition: Excellent (A)
Mileage: 41,300 miles

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-59185R

It fits 4x4 vehicles with a 4.6L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 54,000 miles

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-59186L

It fits 4x4 vehicles with a 4.0L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 83,000 miles

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-59185R

It fits 4x4 vehicles with a 4.0L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 83,000 miles

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-59186L

It is compatible with vehicles equipped with a 4.6L engine, automatic transmission, and 4-wheel drive (4X4).

Condition: Excellent (A)
Mileage: 54,000 miles

2010-2024 Toyota 4Runner Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-59185

Condition: Excellent (A)
Mileage: 71,000 miles

$159.95 View part →

1996-2002 Toyota 4Runner Front Disc Brake Caliper for 15-Inch Wheels - Left (Driver) (Used OEM)

Partslink #: 536-61099L

Condition: Excellent (A)
Mileage: 198,100 miles

2010-2015 Toyota 4Runner 4-Piston Fixed Disc Brake Caliper with Bracket - Front, Right (Passenger) (Used OEM)

Partslink #: 536-51011R

Condition: Excellent (A)
Mileage: 124,000 miles

$149.95 View part →

2025 Toyota 4Runner Disc Brake Caliper - Front (Used OEM)

Partslink #: PB-9052-0000720073

Condition: Excellent (A)
Mileage: 1,000 miles

$189.95 View part →