Pontiac Montana Disc Brake Caliper Replacement

2002-2004 Pontiac Montana Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-00636R

For vehicles with the 3.4L engine and all-wheel drive (AWD).

Condition: Excellent (A)
Mileage: 187,000 miles

2002-2004 Pontiac Montana Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-00637L

Condition: Excellent (A)
Mileage: 187,000 miles

2002-2004 Pontiac Montana Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-00636R

For all-wheel drive (AWD) vehicles.

Condition: Excellent (A)
Mileage: 192,000 miles

2002-2004 Pontiac Montana Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-00637L

It fits 4-door SUV models with all-wheel drive (AWD).

Condition: Excellent (A)
Mileage: 192,000 miles

2005-2009 Pontiac Montana Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-00888L

Condition: Excellent (A)
Mileage: 137,000 miles

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.5, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 456, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.5, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.497, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$55.20 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.5, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 456, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.5, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.497, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (Cardone)

Partslink #: 18-B4639

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket Supplied with Standard Boots

$56.88 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (Cardone)

Partslink #: 18-B4638

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket Supplied with Standard Boots

$56.00 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-17299B

Supplied w/ Mounting Bracket

$57.94 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-17299A

Supplied w/ Mounting Bracket

$57.94 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-17310B

Supplied w/ Mounting Bracket

$58.35 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-17310A

Supplied w/ Mounting Bracket

$58.35 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC11774C

$58.72 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.5, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 456, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.5, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.495, Mounting Hole Thread Diameter: 0.495, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.497, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2005-2009 Pontiac Montana Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-17337A

Supplied w/ Mounting Bracket

$59.37 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (Cardone)

Partslink #: 18-4639

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$59.18 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P17299A

Supplied w/ Mounting Bracket

$64.03 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-17337B

Supplied w/ Mounting Bracket

$59.37 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P17337A

Supplied w/ Mounting Bracket

$65.45 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.66527

$63.79 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-17395A

Supplied w/ Mounting Bracket

$65.69 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P17299B

Supplied w/ Mounting Bracket

$64.03 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Left (Centric)

Partslink #: 142.66032

$71.75 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P17337B

Supplied w/ Mounting Bracket

$65.45 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-00886L

Condition: Excellent (A)
Mileage: 137,000 miles

1999-2005 Pontiac Montana Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-17395B

Supplied w/ Mounting Bracket

$65.69 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.66528

$81.52 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Right (Centric)

Partslink #: 142.66031

$71.75 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3407600

$82.44 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 4103, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.5, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.75, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.62, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1999-2004 Pontiac Montana Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC10842

$71.87 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 18-B4944

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$83.09 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3383152

$75.65 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 4103, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.5, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.75, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.62, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2002-2004 Pontiac Montana Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-47705

$90.21 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 18-B4945

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$83.85 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Left (ACDelco)

Partslink #: W0133-2057064

$96.38 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC11776C

$87.75 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3508107

$98.78 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (Cardone)

Partslink #: W0133-1819913

$87.75 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-17364A

Supplied w/ Mounting Bracket

$99.03 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-47704

$90.21 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (ACDelco)

Partslink #: W0133-2057051

$99.11 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Right (ACDelco)

Partslink #: W0133-2057065

$91.33 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P17364A

Supplied w/ Mounting Bracket

$104.70 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3405013

$98.78 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (Cardone)

Partslink #: W0133-1819912

$107.85 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-17364B

Supplied w/ Mounting Bracket

$99.03 View part →

1999-2004 Pontiac Montana Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: FRC10841N

$122.26 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P17364B

Supplied w/ Mounting Bracket

$104.70 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L5034

$132.14 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (ACDelco)

Partslink #: W0133-2057052

$112.28 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-45019

$134.57 View part →

1999-2004 Pontiac Montana Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC10842N

$122.26 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L4944

$135.84 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.5, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: M10x1.5, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 2.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

2005-2009 Pontiac Montana Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-53006

$129.69 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (Cardone)

Partslink #: 2C-4638

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$140.29 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (ACDelco)

Partslink #: W0133-2056962

$130.31 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L4772A

$141.24 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L5035

$132.14 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-53609

$147.48 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-45018

$134.57 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: FRC11775N

$157.07 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L4945

$135.84 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L4638

$171.60 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-53608

$147.48 View part →

2005-2009 Pontiac Montana Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC11776N

$157.07 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L4639

$171.60 View part →

2002-2004 Pontiac Montana Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L4773A

$177.12 View part →

2005-2009 Pontiac Montana Single Piston Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-00885R

For 4-door van models.

Condition: Excellent (A)
Mileage: 231,000 miles

$55.95 View part →

1999-2005 Pontiac Montana Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-00188R

Condition: Excellent (A)
Mileage: 180,000 miles

2005-2009 Pontiac Montana Single-Piston Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-00887R

Condition: Excellent (A)
Mileage: 137,000 miles