Nissan Murano Disc Brake Caliper Replacement

2003-2007 Nissan Murano Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2792

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$57.63 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-00569B

Supplied w/ Mounting Bracket

$62.66 View part →

2009-2023 Nissan Murano Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: FRC12389

$61.85 View part →

2009-2022 Nissan Murano Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.42593

$67.04 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-00569A

Supplied w/ Mounting Bracket

$62.66 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 3519;4312, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.683, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2007 Nissan Murano Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC11644

$68.04 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 3519;4312, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.683, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2009-2023 Nissan Murano Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B6036

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$65.47 View part →

2009-2023 Nissan Murano Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B6037

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$68.12 View part →

2009-2022 Nissan Murano Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.42594

$67.04 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P00569B

Supplied w/ Mounting Bracket

$68.75 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P00569A

Supplied w/ Mounting Bracket

$68.75 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-00640B

Supplied w/ Mounting Bracket

$72.33 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: T, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2009-2024 Nissan Murano Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-00640A

Supplied w/ Mounting Bracket

$72.33 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Screw Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Powder Coated, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: T, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2011 Nissan Murano Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B2881

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$72.98 View part →

2003-2011 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-P2880

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$73.01 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: T, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2015-2022 Nissan Murano Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.42185

$75.27 View part →

2003-2011 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2880

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$73.98 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P00640B

Supplied w/ Mounting Bracket

$78.14 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P00640A

Supplied w/ Mounting Bracket

$78.14 View part →

2009-2011 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50811R

This part comes complete with the bracket.

Condition: Excellent (A)
Mileage: 156,000 miles

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: No, Caliper Type: Floating, Casting Number: 4319, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.42, Mounting Hole Thread Diameter: 0.42, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.683, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2009-2023 Nissan Murano Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-6036

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$79.24 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L6037

$83.25 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.42144

$84.00 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 2046, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.42143

$84.00 View part →

2015-2023 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B7100

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$85.14 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 31, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.315, Mounting Hole Thread Diameter: 0.315, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2007 Nissan Murano Disc Brake Caliper - Rear Right (Centric)

Partslink #: 142.42561

$84.11 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-2870

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$86.77 View part →

2003-2012 Nissan Murano Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00576B

Supplied w/ Mounting Bracket

$87.19 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 2046, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2012 Nissan Murano Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00576A

Supplied w/ Mounting Bracket

$87.19 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Screw Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Powder Coated, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 31, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2015-2023 Nissan Murano Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B7101

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$87.41 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 31, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-P2870B

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$89.43 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 31, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B2871B

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$88.59 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 31, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.315, Mounting Hole Thread Diameter: 0.315, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.77, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2870B

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$91.62 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-2871

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$89.79 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L6036

$92.60 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-67648

$94.40 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-67649

$94.40 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2793

$95.40 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2792

$95.40 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-67668

$96.49 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-67669

$96.49 View part →

2003-2007 Nissan Murano Disc Brake Caliper - Rear Right (Cardone)

Partslink #: W0133-1824635

$96.57 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00648A

Supplied w/ Mounting Bracket

$103.43 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00648B

Supplied w/ Mounting Bracket

$103.43 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00648A

Supplied w/ Mounting Bracket

$108.81 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00648B

Supplied w/ Mounting Bracket

$108.81 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00621A

Supplied w/ Mounting Bracket

$109.86 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00621B

Supplied w/ Mounting Bracket

$109.86 View part →

2009-2023 Nissan Murano Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3402881

Production: 10/01/2008-

$111.96 View part →

2009-2023 Nissan Murano Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3488310

Production: 10/01/2008-

$110.92 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2870B

$123.13 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2871B

$123.13 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-68023

$134.08 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-68022

$134.08 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3443758

$134.70 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3345669

$134.70 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-67147

2015-2024 Nissan Murano Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-67146

2003-2011 Nissan Murano Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-67095

2003-2011 Nissan Murano Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-67094

2003-2011 Nissan Murano Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2880

$147.23 View part →

2003-2011 Nissan Murano Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2881

$147.23 View part →

2015-2023 Nissan Murano Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3347764

$160.13 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 2.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

2015-2023 Nissan Murano Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3386311

$160.13 View part →

2003-2011 Nissan Murano Disc Brake Caliper - Front Left (Cardone)

Partslink #: 2C-2880

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$170.12 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L7101

$177.35 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L7100

$177.35 View part →

2009-2024 Nissan Murano Standard Single-Piston Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 56,000 miles

2009-2024 Nissan Murano Standard Single-Piston Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 67,000 miles

2009-2024 Nissan Murano Standard Single-Piston Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 58,000 miles

2009-2024 Nissan Murano Standard Single-Piston Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 39,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 67,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It was removed from a 4-door vehicle.

Condition: Excellent (A)
Mileage: 56,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 58,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 39,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

For 4-door SUV models.

Condition: Excellent (A)
Mileage: 56,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 67,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 39,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 58,000 miles

2004-2007 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-59931R

Condition: Excellent (A)
Mileage: 181,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-61193

Condition: Excellent (A)
Mileage: 27,000 miles

2015-2024 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-61192

Condition: Excellent (A)
Mileage: 19,000 miles

$89.95 View part →

2004-2007 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-59932L

Condition: Excellent (A)
Mileage: 181,000 miles

2025-2026 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-11179R

For 4-door SUV models.

Condition: Excellent (A)

$102.95 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

For vehicles with the 3.7L engine, automatic transmission, and rear-wheel drive (RWD).

Condition: Excellent (A)
Mileage: 53,000 miles

2025 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 29,000 miles

2011-2014 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

For vehicles with the 3.5L engine, continuously variable transmission (CVT), and all-wheel drive (AWD).

Condition: Excellent (A)
Mileage: 144,000 miles

2025 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 7,000 miles

2009-2011 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-50812L

It is compatible with vehicles equipped with a 3.5L engine, continuously variable transmission (CVT), and all-wheel drive (AWD).

Condition: Excellent (A)
Mileage: 286,000 miles

2025 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 22,000 miles

$149.95 View part →

2015-2024 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-61193

Condition: Excellent (A)
Mileage: 19,000 miles

$89.95 View part →

2025 Nissan Murano Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 10,000 miles

$179.95 View part →

2011-2014 Nissan Murano Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 72,000 miles

$104.95 View part →

2011-2014 Nissan Murano Front Disc Brake Caliper - Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 53,800 miles

Sale price: $109.95

$91.95 View part →

2025 Nissan Murano Rear Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

It fits vehicles with a 2.0L engine, automatic transmission, and all-wheel drive.

Condition: Excellent (A)

$332.95 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

It fits 4-door SUV models.

Condition: Excellent (A)
Mileage: 67,000 miles

2025 Nissan Murano Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

It fits vehicles with a 2.0L engine, automatic transmission, and all-wheel drive.

Condition: Excellent (A)

$415.95 View part →

2009-2024 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

It was removed from a 4-door SUV.

Condition: Excellent (A)
Mileage: 58,000 miles

2009-2024 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 56,000 miles

2009-2024 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 39,000 miles

2003-2007 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-59427L

Condition: Excellent (A)
Mileage: 181,000 miles

2009-2024 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-50814

Condition: Excellent (A)
Mileage: 19,000 miles

$89.95 View part →

2025 Nissan Murano Rear Disc Brake Caliper - Front, Left (Driver) (Used OEM)

It fits vehicles with a 2.0L engine, automatic transmission, and all-wheel drive.

Condition: Excellent (A)

$332.95 View part →

2025 Nissan Murano Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

It fits vehicles with a 2.0L engine, automatic transmission, and all-wheel drive.

Condition: Excellent (A)

$415.95 View part →

2003-2007 Nissan Murano Single Piston Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-59426R

Condition: Excellent (A)
Mileage: 145,000 miles

$69.95 View part →

2011-2014 Nissan Murano 2-Piston Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50412R

It fits vehicles with a 3.5L engine, continuously variable transmission (CVT), and all-wheel drive (AWD).

Condition: Excellent (A)
Mileage: 144,000 miles

2025 Nissan Murano Disc Brake Caliper Assembly - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 30,000 miles

$109.95 View part →

2025 Nissan Murano Disc Brake Caliper Assembly - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 29,000 miles

2025 Nissan Murano Disc Brake Caliper Assembly - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 7,000 miles

2025 Nissan Murano Disc Brake Caliper Assembly - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 22,000 miles

$149.95 View part →

2025-2026 Nissan Murano Disc Brake Caliper with Hose - Front, Left (Driver) (Used OEM)

It fits vehicles with a 2.0L engine, automatic transmission, and all-wheel drive.

Condition: Excellent (A)
Mileage: 2,000 miles

$116.95 View part →

2025-2026 Nissan Murano Disc Brake Caliper with Hose - Front, Left (Driver) (Used OEM)

It fits 4x4 vehicles with a 3.5L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 3,000 miles

$116.95 View part →

2025-2026 Nissan Murano Disc Brake Caliper with Hose - Front, Left (Driver) (Used OEM)

It is for a 4x4 vehicle with a 3.5L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 33,000 miles

2025-2026 Nissan Murano Disc Brake Caliper with Hose - Front, Left (Driver) (Used OEM)

It fits 4x4 vehicles with a 3.5L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 51,000 miles