Mazda 6 Disc Brake Caliper Replacement

2009-2013 Mazda 6 Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-50792L

It was removed from a 4-door sedan.

Condition: Excellent (A)
Mileage: 172,000 miles

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Gj6e, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.248, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2005 Mazda 6 Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B2707

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$56.51 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-59958L

It fits 4-door vehicles.

Condition: Excellent (A)
Mileage: 172,000 miles

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 777, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.24, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2006-2007 Mazda 6 Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B3445

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$61.51 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.45084

$43.54 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 777, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.24, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2003-2005 Mazda 6 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01162B

Supplied w/ Mounting Bracket

$62.62 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 777, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.397, Mounting Hole Thread Diameter: 0.397, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.24, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2006-2007 Mazda 6 Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B3444

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$60.77 View part →

2006-2007 Mazda 6 Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-3445

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$64.71 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC11909

$62.31 View part →

2006-2007 Mazda 6 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01178B

Supplied w/ Mounting Bracket

$64.84 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-01162A

Supplied w/ Mounting Bracket

$62.62 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P02012A

Supplied w/ Mounting Bracket

$65.12 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P02012B

Supplied w/ Mounting Bracket

$65.12 View part →

Supplied w/ Mounting Bracket

$66.32 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Dbud, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.25, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2006-2013 Mazda 6 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-17929A

Supplied w/ Mounting Bracket

$66.32 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Right (Cardone)

Partslink #: 18-B5001

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$66.71 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P01162A

Supplied w/ Mounting Bracket

$68.69 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P01162B

Supplied w/ Mounting Bracket

$68.69 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P17929A

Supplied w/ Mounting Bracket

$72.43 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P17929B

Supplied w/ Mounting Bracket

$72.43 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Pnr57, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 2.25, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.61556

$83.48 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B7173

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$81.46 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P02002A

Supplied w/ Mounting Bracket

$84.17 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.61555

$83.48 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.45552

$89.50 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P02002B

Supplied w/ Mounting Bracket

$84.17 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P17930A

Supplied w/ Mounting Bracket

$89.86 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.45583

Electronic Parking Brake

$87.63 View part →

2006-2007 Mazda 6 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.45558

$90.21 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P17930B

Supplied w/ Mounting Bracket

$89.86 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: FRC11931

$93.26 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01163B

Supplied w/ Mounting Bracket

$95.34 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (WBR)

Partslink #: W0133-1906222

$94.78 View part →

2014-2015 Mazda 6 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-02001A

Supplied w/ Mounting Bracket

$95.81 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01163A

Supplied w/ Mounting Bracket

$95.34 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-02002B

Supplied w/ Mounting Bracket

$95.82 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 150, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.316, Mounting Hole Thread Diameter: 0.316, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.335, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2014-2015 Mazda 6 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-02001B

Supplied w/ Mounting Bracket

$95.81 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 18-5003

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$96.60 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-02002A

Supplied w/ Mounting Bracket

$95.82 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-17930B

Supplied w/ Mounting Bracket

$97.56 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-17930A

Supplied w/ Mounting Bracket

$97.56 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3379785

$99.40 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3429738

$99.40 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01163B

Supplied w/ Mounting Bracket

$101.03 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01163A

Supplied w/ Mounting Bracket

$101.03 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2707

$107.90 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2706

$107.90 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Right (Cardone)

Partslink #: W0133-1787361

$112.31 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Front Left (Cardone)

Partslink #: W0133-1756405

$112.31 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2859

$118.76 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2858

$118.76 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3445890

$122.61 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Left (Cardone)

Partslink #: W0133-1892890

$123.85 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L5001

$124.74 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L5000

$124.74 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-54098

$124.81 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L5002

$125.46 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L5003

$125.46 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-54645

$132.62 View part →

2006-2013 Mazda 6 Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: RC11932C

$134.56 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-80107

$136.76 View part →

2014-2017 Mazda 6 Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-80660

$138.37 View part →

2014-2017 Mazda 6 Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-80661

$138.37 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-80642

$150.51 View part →

2003-2005 Mazda 6 Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-80643

$150.51 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Powder Coated, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: K3604, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.323, Mounting Hole Thread Diameter: 0.323, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.503, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2014-2021 Mazda 6 Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3360256

$152.63 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Powder Coated, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: K3604, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.323, Mounting Hole Thread Diameter: 0.323, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.503, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2016-2021 Mazda 6 Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B7435

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$152.73 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B7434

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$157.08 View part →

2014-2015 Mazda 6 Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3410068

$159.05 View part →

2014-2015 Mazda 6 Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3425268

$159.05 View part →

2014-2021 Mazda 6 Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3347250

$163.29 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-4430445

$195.27 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-4430456

$195.27 View part →

2009-2013 Mazda 6 Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-50791R

Built for a 4-door vehicle.

Condition: Excellent (A)
Mileage: 172,000 miles

2006-2013 Mazda 6 Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-59957R

It fits 4-door vehicles.

Condition: Excellent (A)
Mileage: 172,000 miles

2016-2021 Mazda 6 Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-10868R

Condition: Good (B)
Mileage: 82,400 miles

$103.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-10868R

Condition: Excellent (A)
Mileage: 81,800 miles

$104.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-10868R

Condition: Excellent (A)
Mileage: 47,800 miles

2016-2021 Mazda 6 Disc Brake Caliper with Hose - Front, Left (Driver) (Used OEM)

Partslink #: 536-10869L

It was removed from a 4-door sedan.

Condition: Excellent (A)
Mileage: 59,000 miles

$79.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper with Hose - Front, Left (Driver) (Used OEM)

Partslink #: 536-10869L

Condition: Good (B)
Mileage: 82,400 miles

$103.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper with Electric Parking Brake Motor - Rear, Left (Driver) (Used OEM)

Partslink #: 536-10871L

It was removed from a 4-door sedan.

Condition: Excellent (A)
Mileage: 59,000 miles

$79.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper with Electric Parking Brake Motor - Rear, Left (Driver) (Used OEM)

Partslink #: 536-10871L

Condition: Good (B)
Mileage: 82,400 miles

$139.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper with Motor - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-10870R

It is for a front-wheel drive vehicle with a 2.5L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 87,000 miles

$89.95 View part →

2016-2021 Mazda 6 Disc Brake Caliper with Motor - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-10870R

It is for a front-wheel drive vehicle with a 2.5L engine and automatic transmission.

Condition: Excellent (A)
Mileage: 82,000 miles

$139.95 View part →

2014-2015 Mazda 6 Disc Brake Caliper with Bracket - Front, Right (Passenger) (Used OEM)

Partslink #: 536-61306R

This part comes complete with the bracket.

Condition: Excellent (A)
Mileage: 118,000 miles

2014-2015 Mazda 6 Disc Brake Caliper with Bracket - Front, Left (Driver) (Used OEM)

Partslink #: 536-61307L

This part includes the bracket.

Condition: Excellent (A)
Mileage: 118,000 miles

2014-2015 Mazda 6 Disc Brake Caliper with Bracket - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-61304R

This part includes the mounting bracket.

Condition: Excellent (A)
Mileage: 118,000 miles

2014-2015 Mazda 6 Disc Brake Caliper with Bracket - Rear, Left (Driver) (Used OEM)

Partslink #: 536-61305L

This part includes the mounting bracket.

Condition: Excellent (A)
Mileage: 118,000 miles