Bellows Color: Black, Contains Electronic Components: No, Does it require SDS: No, End To End Length: 34.5, FAA_A1: The Most Likely Cause Of A Power Steering Pump Whine Is Air In The System. The Steering System Must Be Bled. This May Take A Few Attempts Depending On The Design Of The System., FAA_A2: The Geometry Of The Front Suspension Is Designed To Return The Steering Wheel To Center Coming Out Of A Turn. If The Steering Wheel Is Not Returning To Center On Its Own When Coming Out Of A Turn, Check The Front-end Alignment Settings And Inspect For Bin, FAA_A3: No. The Rack And Pinion Has Been Adjusted At The Factory. No Additional Adjustment Is Necessary. Try Isolating The Rack To Find Out Where The Play Exists. If You Hold The Inner Tie Rod And Have Someone Turn The Wheel, Does The Play Disappear? If So, The P, FAA_A4: Yes, The Boot Clamps Must Be Loosened To Set The Toe Adjustment When Performing A Front-end Alignment. Failure To Loosen The Clamps Will Twist The Boots During Turning Maneuvers Causing Cracks To Form On Boot. Once The Boot Is Torn, Road Debris And Water , FAQ_Q1: I Replaced The Rack And Now The Power Steering Pump Is Whining. It Never Did This Before! What Happened?, FAQ_Q2: The Steering Wheel Is Not Returning To Center Coming Out Of A Turn. What Could Be Causing This? , FAQ_Q3: The Replacement Rack And Pinion Is Installed And The Steering Wheel Has Too Much Play. Should I Adjust The Rack?, FAQ_Q4: Are There Any Steps That Should Be Done Prior To Alignment?, Gasket Or Seal Included: Yes, Grade Type: Regular, Inlet Line Fitting Diameter: 0.702, Inlet Line Fitting Gender: Male, Inner Tie Rods Included: No, Input Shaft Type: Grooved, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Brackets Included: No, Mounting Hardware Included: Yes, Mounting Hole Quantity: 2, Outer Tie Rods Included: No, Outlet Line Fitting Diameter: 0.459, Outlet Line Fitting Gender: Male, Product Condition: Remanufactured, Steering Input Shaft Diameter: 0.725, Total Turns Lock To Lock: 3.125, Type: Hydraulic

1993-1995 Dodge Intrepid Rack and Pinion Assembly (Cardone)

Partslink #: 22-324

Supplied without Inner Tie Rods with Hydraulic Power For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system In-Line Filter available

$202.98 View part →

✓ In Stock

1994-1995 Dodge Intrepid Rack and Pinion Assembly (Mapco)

Partslink #: 95214M

With Speed Proportional steering Unit is a center take off design and is sold without inner tie rods - includes electronic solenoid

$227.06 View part →

✓ In Stock

1998-2004 Dodge Intrepid Rack and Pinion Assembly (Mapco)

Partslink #: 95312M

Without Speed Proportional steering Unit is a center take off design and is sold without inner tie rods

$302.25 View part →

Bellows Color: Black, Contains Electronic Components: No, Does it require SDS: No, End To End Length: 34.625, FAA_A1: The Most Likely Cause Of A Power Steering Pump Whine Is Air In The System. The Steering System Must Be Bled. This May Take A Few Attempts Depending On The Design Of The System., FAA_A2: The Geometry Of The Front Suspension Is Designed To Return The Steering Wheel To Center Coming Out Of A Turn. If The Steering Wheel Is Not Returning To Center On Its Own When Coming Out Of A Turn, Check The Front-end Alignment Settings And Inspect For Bin, FAA_A3: No. The Rack And Pinion Has Been Adjusted At The Factory. No Additional Adjustment Is Necessary. Try Isolating The Rack To Find Out Where The Play Exists. If You Hold The Inner Tie Rod And Have Someone Turn The Wheel, Does The Play Disappear? If So, The P, FAA_A4: Yes, The Boot Clamps Must Be Loosened To Set The Toe Adjustment When Performing A Front-end Alignment. Failure To Loosen The Clamps Will Twist The Boots During Turning Maneuvers Causing Cracks To Form On Boot. Once The Boot Is Torn, Road Debris And Water , FAQ_Q1: I Replaced The Rack And Now The Power Steering Pump Is Whining. It Never Did This Before! What Happened?, FAQ_Q2: The Steering Wheel Is Not Returning To Center Coming Out Of A Turn. What Could Be Causing This? , FAQ_Q3: The Replacement Rack And Pinion Is Installed And The Steering Wheel Has Too Much Play. Should I Adjust The Rack?, FAQ_Q4: Are There Any Steps That Should Be Done Prior To Alignment?, Gasket Or Seal Included: Yes, Grade Type: Regular, Inlet Line Fitting Diameter: 0.702, Inlet Line Fitting Gender: Male, Inner Tie Rods Included: No, Input Shaft Type: Grooved, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Brackets Included: No, Mounting Hardware Included: No, Mounting Hole Quantity: 4, Outer Tie Rods Included: No, Outlet Line Fitting Diameter: 0.459, Outlet Line Fitting Gender: Male, Product Condition: Remanufactured, Steering Input Shaft Diameter: 0.725, Total Turns Lock To Lock: 3.125, Type: Hydraulic

✓ In Stock

1998-2004 Dodge Intrepid Rack and Pinion Assembly (Cardone)

Partslink #: 22-345

Supplied without Inner Tie Rods with Hydraulic Power with Performance Steering (SBP) with Standard Steering (SBA) For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system In-Line Filter available Sales Codes are found on the "Body Code" plate located on the left front side shield, wheel housing, or the upper radiator support of your vehicle