Connector Gender: Male, Connector Quantity: 2, Connector Shape: Rectangle, FAA_A1: “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission., FAA_A2: Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module., FAA_A3: No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application., FAA_A4: Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn., FAA_A5: Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays., FAA_A6: Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System., FAA_A7: Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details., FAA_A8: Chrysler Models 1996 And Newer Will Need To Be Vin Programmed., FAA_A9: Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Fuel Injection, Loss Of Pulse On Fuel Pump, Intermittent Starting Problems., FAQ_Q1: What’s The Difference Between An Ecm And A Pcm?, FAQ_Q2: Do I Have To Transfer Anything From My Original Ecm/pcm?, FAQ_Q3: Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?, FAQ_Q4: The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?, FAQ_Q5: What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?, FAQ_Q6: Do Gm Vehicles Have A Passive Anti-theft System?, FAQ_Q7: Do I Need A Scanner To Reset The Anti-theft System, FAQ_Q8: Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?, FAQ_Q9: What Are The Most Common Symptoms Of A Bad Pcm?, Flash Programming Required: No, Flashable: No, Mounting Hardware Included: No, Mounting Hole Quantity: 4, Product Condition: Remanufactured, Removable PROM: No, Terminal Gender: Male, Terminal Quantity: 24, Terminal Type: Pin

1988 Dodge Dakota Engine Control Module (ECM) (Cardone)

Partslink #: 79-9634

This Unit is Pre-Programmed at the Factory with Original Equipment (OE) # 4379581, 4379634

$257.51 View part →

Connector Gender: Female, Connector Quantity: 3, Connector Shape: Rectangle, FAA_A1: “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission., FAA_A2: Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module., FAA_A3: No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application., FAA_A4: Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn., FAA_A5: Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays., FAA_A6: Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System., FAA_A7: Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details., FAA_A8: Chrysler Models 1996 And Newer Will Need To Be Vin Programmed., FAA_A9: Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Fuel Injection, Loss Of Pulse On Fuel Pump, Intermittent Starting Problems., FAQ_Q1: What’s The Difference Between An Ecm And A Pcm?, FAQ_Q2: Do I Have To Transfer Anything From My Original Ecm/pcm?, FAQ_Q3: Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?, FAQ_Q4: The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?, FAQ_Q5: What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?, FAQ_Q6: Do Gm Vehicles Have A Passive Anti-theft System?, FAQ_Q7: Do I Need A Scanner To Reset The Anti-theft System, FAQ_Q8: Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?, FAQ_Q9: What Are The Most Common Symptoms Of A Bad Pcm?, Flash Programming Required: No, Flashable: Yes, Mounting Hardware Included: No, Mounting Hole Quantity: 3, Product Condition: Remanufactured, Removable PROM: No, Terminal Gender: Male, Terminal Quantity: 96, Terminal Type: Pin

✓ In Stock

2002 Dodge Dakota Engine Control Module (ECM) (Cardone)

Partslink #: 79-9320V

with Original Equipment (OE) # 5602 9352AA-AC Important: Vehicle Specific Flash Programming Required ON or OFF the Vehicle. Accurate VIN and Mileage are Required

$297.09 View part →

Connector Gender: Male, Connector Quantity: 2, Connector Shape: Rectangle, FAA_A1: “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission., FAA_A2: Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module., FAA_A3: No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application., FAA_A4: Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn., FAA_A5: Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays., FAA_A6: Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System., FAA_A7: Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details., FAA_A8: Chrysler Models 1996 And Newer Will Need To Be Vin Programmed., FAA_A9: Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Fuel Injection, Loss Of Pulse On Fuel Pump, Intermittent Starting Problems., FAQ_Q1: What’s The Difference Between An Ecm And A Pcm?, FAQ_Q2: Do I Have To Transfer Anything From My Original Ecm/pcm?, FAQ_Q3: Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?, FAQ_Q4: The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?, FAQ_Q5: What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?, FAQ_Q6: Do Gm Vehicles Have A Passive Anti-theft System?, FAQ_Q7: Do I Need A Scanner To Reset The Anti-theft System, FAQ_Q8: Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?, FAQ_Q9: What Are The Most Common Symptoms Of A Bad Pcm?, Flash Programming Required: Yes, Flashable: Yes, Mounting Hardware Included: No, Mounting Hole Quantity: 2, Product Condition: Remanufactured, Removable PROM: No, Terminal Gender: Male, Terminal Quantity: 80, Terminal Type: Pin

✓ In Stock

1997 Dodge Dakota Engine Control Module (ECM) (Cardone)

Partslink #: 79-0376

This Unit is Pre-Programmed at the Factory

$308.90 View part →

Connector Gender: Female, Connector Quantity: 3, Connector Shape: Rectangle, FAA_A1: “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission., FAA_A2: Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module., FAA_A3: No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application., FAA_A4: Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn., FAA_A5: Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays., FAA_A6: Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System., FAA_A7: Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details., FAA_A8: Chrysler Models 1996 And Newer Will Need To Be Vin Programmed., FAA_A9: Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Fuel Injection, Loss Of Pulse On Fuel Pump, Intermittent Starting Problems., FAQ_Q1: What’s The Difference Between An Ecm And A Pcm?, FAQ_Q2: Do I Have To Transfer Anything From My Original Ecm/pcm?, FAQ_Q3: Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?, FAQ_Q4: The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?, FAQ_Q5: What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?, FAQ_Q6: Do Gm Vehicles Have A Passive Anti-theft System?, FAQ_Q7: Do I Need A Scanner To Reset The Anti-theft System, FAQ_Q8: Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?, FAQ_Q9: What Are The Most Common Symptoms Of A Bad Pcm?, Flash Programming Required: No, Flashable: Yes, Mounting Hardware Included: No, Mounting Hole Quantity: 3, Product Condition: Remanufactured, Removable PROM: No, Terminal Gender: Male, Terminal Quantity: 96, Terminal Type: Pin

✓ In Stock

2000 Dodge Dakota Engine Control Module (ECM) (Cardone)

Partslink #: 79-0360V

with Original Equipment (OE) # 5604 0360AB thru AH Important: Vehicle Specific Flash Programming Required ON or OFF the Vehicle. Accurate VIN and Mileage are Required

$312.50 View part →

✓ In Stock

1999 Dodge Dakota Engine Control Module (ECM) (Dorman)

Partslink #: 318-110

Federal Emissions Pre-Programmed Unit VIN, Mileage And Tire Size Required To Order

$317.04 View part →

✓ In Stock

2002 Dodge Dakota Engine Control Module (ECM) (Dorman)

Partslink #: 318-102

Federal Emissions Pre-Programmed Unit Quad Cab VIN, Mileage And Tire Size Required To Order

$327.11 View part →

✓ In Stock

2002 Dodge Dakota Engine Control Module (ECM) (Dorman)

Partslink #: 318-107

Federal Emissions Pre-Programmed Unit Quad Cab VIN, Mileage And Tire Size Required To Order

$334.86 View part →

✓ In Stock

2007 Dodge Dakota Engine Control Module (ECM) (Dorman)

Partslink #: 318-048

Pre-Programmed Unit VIN, Mileage And Tire Size Required To Order

$386.76 View part →

Connector Gender: Female, Connector Quantity: 3, Connector Shape: Rectangle, FAA_A1: “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission., FAA_A2: Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module., FAA_A3: No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application., FAA_A4: Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn., FAA_A5: Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays., FAA_A6: Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System., FAA_A7: Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details., FAA_A8: Chrysler Models 1996 And Newer Will Need To Be Vin Programmed., FAA_A9: Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Fuel Injection, Loss Of Pulse On Fuel Pump, Intermittent Starting Problems., FAQ_Q1: What’s The Difference Between An Ecm And A Pcm?, FAQ_Q2: Do I Have To Transfer Anything From My Original Ecm/pcm?, FAQ_Q3: Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?, FAQ_Q4: The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?, FAQ_Q5: What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?, FAQ_Q6: Do Gm Vehicles Have A Passive Anti-theft System?, FAQ_Q7: Do I Need A Scanner To Reset The Anti-theft System, FAQ_Q8: Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?, FAQ_Q9: What Are The Most Common Symptoms Of A Bad Pcm?, Flash Programming Required: No, Flashable: Yes, Mounting Hardware Included: No, Mounting Hole Quantity: 3, Product Condition: Remanufactured, Removable PROM: No, Terminal Gender: Male, Terminal Quantity: 96, Terminal Type: Pin

✓ In Stock

2000 Dodge Dakota Engine Control Module (ECM) (Cardone)

Partslink #: 79-0429V

with Original Equipment (OE) # 5604 0429AB thru AH Important: Vehicle Specific Flash Programming Required ON or OFF the Vehicle. Accurate VIN and Mileage are Required