BMW 323i Disc Brake Caliper Replacement

1997-2000 BMW 323i Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B1619

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$53.12 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.34575

$58.25 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 40/19, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.572, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1998-2000 BMW 323i Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-02314B

Supplied w/ Mounting Bracket

$58.09 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 40/19, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.572, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1997-2000 BMW 323i Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B2640

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$61.40 View part →

1997-2000 BMW 323i Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2641

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$59.74 View part →

2006-2011 BMW 323i Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.34107

$64.42 View part →

2000 BMW 323i Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-02337B

Supplied w/ Mounting Bracket

$70.67 View part →

2006-2007 BMW 323i Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.34075

w/o Bracket

$67.23 View part →

1998-1999 BMW 323i Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-02316B

Supplied w/ Mounting Bracket w/ Solid Disc

$73.78 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 911, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.725, Mounting Hole Thread Diameter: 0.725, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.651, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2000 BMW 323i Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-02337A

Supplied w/ Mounting Bracket

$70.67 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-3226

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$74.25 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 911, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.651, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1998-1999 BMW 323i Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-02316A

Supplied w/ Mounting Bracket w/ Solid Disc

$73.78 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M8x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 911, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.651, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2006-2011 BMW 323i Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B3226

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$76.39 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B3227

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$78.80 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 57/24, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.242, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2006-2011 BMW 323i Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-02390A

Supplied w/ Mounting Bracket

$90.34 View part →

2006-2011 BMW 323i Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B3360

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$79.35 View part →

2000 BMW 323i Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-31647

$90.83 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-02390B

Supplied w/ Mounting Bracket

$90.34 View part →

1998-1999 BMW 323i Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-31615

Solid Rear Disc

$90.83 View part →

1998-1999 BMW 323i Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-31614

Solid Rear Disc

$90.83 View part →

2006-2011 BMW 323i Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-02397B

Supplied w/ Mounting Bracket

$94.12 View part →

Supplied w/ Mounting Bracket

$94.12 View part →

2000 BMW 323i Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L1619A

$108.98 View part →

1998-2000 BMW 323i Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L1618

$98.24 View part →

2000 BMW 323i Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2641A

$142.93 View part →

2000 BMW 323i Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L1618A

$108.98 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3373886

$151.90 View part →

1998-2000 BMW 323i Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3399597

$111.41 View part →

1998-2000 BMW 323i Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2641

$170.00 View part →

1998-1999 BMW 323i Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3482071

$115.23 View part →

2006-2007 BMW 323i Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3423185

$192.54 View part →

2000 BMW 323i Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2640A

$142.93 View part →

2007-2011 BMW 323i Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3446786

Production: 03/01/2007-

$205.19 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3493441

$151.90 View part →

1998-2000 BMW 323i Disc Brake Caliper - Front Left (ATE)

Partslink #: W0133-1662192

$221.69 View part →

2007-2011 BMW 323i Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3354932

$164.58 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Left (ATE)

Partslink #: W0133-1779667

$263.03 View part →

1998-2000 BMW 323i Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2640

$170.00 View part →

2006-2007 BMW 323i Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3490745

$192.54 View part →

1998-2000 BMW 323i Disc Brake Caliper - Front Right (ATE)

Partslink #: W0133-1601186

$197.48 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear Right (ATE)

Partslink #: W0133-1779668

$303.68 View part →

2006-2011 BMW 323i Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-50269R

Condition: Excellent (A)
Mileage: 125,000 miles

2006-2011 BMW 323i Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-50270L

This part fits the rear of the vehicle.

Condition: Excellent (A)
Mileage: 125,000 miles

2007-2011 BMW 323i Standard Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Partslink #: 536-50539R

Condition: Excellent (A)
Mileage: 125,000 miles

2007-2011 BMW 323i Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-50541L

Condition: Excellent (A)
Mileage: 125,000 miles

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-4756

For vehicles with the B46 engine. Fits BMW G01, G02, G20, and G42 chassis.

Condition: Excellent (A)

$79.95 View part →

2019-2024 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-33363

For vehicles with the B46 engine. Fits BMW G01, G02, G20, and G42 chassis.

Condition: Excellent (A)
Mileage: 45,000 miles

$79.95 View part →

2019-2024 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-44759

For vehicles with the B46 engine. Fits BMW G01, G02, G20, and G42 chassis.

Condition: Excellent (A)
Mileage: 108,100 miles

$79.95 View part →

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-1891

This brake caliper fits BMW G01, G20, G22, G23, G26, and G29 chassis.

Condition: Excellent (A)

$104.95 View part →

2019-2026 BMW 323i Front Brake Caliper (Used OEM)

Partslink #: OEMG-4054

For vehicles with the B46B20O1 engine. Fits BMW G01, G20, G22, G23, G26, and G29 chassis.

Condition: Excellent (A)

$104.95 View part →

2019-2025 BMW 323i Front Brake Caliper (Used OEM)

Partslink #: OEMG-52665

For G05, G06, 40, G26, 430, G30, 530, and 540 models, this fits PRE-LCI (pre-facelift) vehicles only. For G22, G23, 430, G30, and 530 models, this fits LCI (facelift) vehicles only. Fits BMW G05, G06, G20, G22, G23, G26, and G30 chassis.

Condition: Excellent (A)
Mileage: 154,000 miles

$125.95 View part →

2019-2025 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-38584

For vehicles with the B46B20O1 engine. Fits BMW G01, G20, G22, G23, G26, and G29 chassis.

Condition: Excellent (A)
Mileage: 9,700 miles

$136.95 View part →

2019-2026 BMW 323i Front Right Brake Caliper (Used OEM)

Partslink #: OEMG-25555

It is intact. For vehicles with the B58 engine and automatic transmission. Fits BMW G05, G06, G20, G22, G26, and G30 chassis.

Condition: Excellent (A)

2019-2026 BMW 323i Front Left Brake Caliper (Used OEM)

Partslink #: OEMG-29295

The part is intact. For vehicles with the B58 engine and automatic transmission. Fits BMW G05, G06, G20, G22, G23, G26, and G30 chassis.

Condition: Excellent (A)

2019-2026 BMW 323i Rear Brake Caliper (Used OEM)

Partslink #: OEMG-44571

For vehicles with the B46B20O1 engine. Fits BMW G20, G22, G23, G26, and G42 chassis.

Condition: Excellent (A)
Mileage: 63,000 miles

2019-2026 BMW 323i Rear Brake Caliper (Used OEM)

Partslink #: OEMG-46769

It is a rear brake caliper for vehicles with the B46B20O1 engine. Fits BMW G20, G22, G23, G26, and G42 chassis.

Condition: Excellent (A)
Mileage: 109,100 miles

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-38799

It fits vehicles with the B58B30M1 engine. For G05, G06, G26, and G30 chassis models, this fits pre-LCI (pre-facelift) vehicles only. For G22, G23, and G30 chassis models, this fits LCI (facelift) vehicles only. Fits BMW G05, G06, G20, G22, G23, G26, and G30 chassis.

Condition: Excellent (A)
Mileage: 45,100 miles

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-3610

It shows normal signs of use such as nicks, scuffs, and scratches. For vehicles with the B58B30M1 engine. Fits BMW G05, G06, G20, G22, G23, G26, and G30 chassis.

Condition: Excellent (A)

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-3611

Fits BMW G05, G06, G20, G22, G23, G26, and G30 chassis.

Condition: Excellent (A)

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-60447

Fits BMW G05, G06, G20, G22, G23, G26, and G30 chassis. For G05, G06, G26, and G30 models, this fits pre-LCI (pre-facelift) vehicles only. For G22, G23, and G30 models, this fits LCI (facelift) vehicles only.

Condition: Excellent (A)

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-38586

For vehicles with the B46B20O1 engine. Fits BMW G20, G22, G23, G26, G42, and G29 chassis.

Condition: Excellent (A)
Mileage: 9,700 miles

2019-2021 BMW 323i Rear Brake Caliper (Used OEM)

Partslink #: OEMG-3757

For vehicles with engine code B46B20O1. Fits BMW G20, G22, G23, G26, and G42 chassis.

Condition: Excellent (A)

$204.95 View part →

2019-2024 BMW 323i Disc Brake Caliper - Rear (Used OEM)

Partslink #: PB-6494-0000074901

Condition: Excellent (A)
Mileage: 9,000 miles

$275.95 View part →

2012-2019 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-41487

This is a Brembo brake caliper. For vehicles with the N55B30M0 engine. Fits BMW F30, F32, F33, and F36 chassis.

Condition: Excellent (A)
Mileage: 149,400 miles

$295.95 View part →

2019-2026 BMW 323i Rear Brake Caliper with Parking Brake Motor (Used OEM)

Partslink #: BMA-027401

It has scratches, and the electronic parking brake motor housing is cracked. Please verify your part identification number matches. Fits BMW G20, G22, and G26 chassis.

Condition: Excellent (A)

$314.95 View part →

2019-2025 BMW 323i M Sport Disc Brake Caliper - Rear (Used OEM)

Partslink #: PB-7888-0000237579

Condition: Excellent (A)
Mileage: 42,000 miles

$329.95 View part →

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-34249

It is a Brembo brand part. Fits BMW G01, G02, G20, and G42 chassis.

Condition: Excellent (A)

$336.95 View part →

2012-2019 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-39050

This Brembo brake caliper is blue. It has scratches and is missing hardware. Fits BMW F22, F23, F30, and F32 chassis.

Condition: Excellent (A)

$399.95 View part →

2019-2026 BMW 323i Front Brake Caliper (Used OEM)

Partslink #: OEMG-30071

This Brembo brake caliper is blue. It fits vehicles with the B58M engine. Please verify compatibility before purchasing as an upgrade. Fits BMW G01 and G20 chassis.

Condition: Excellent (A)

$399.95 View part →

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: BMA-027402

It has scratches and scuffs. Please verify your part number matches. Fits BMW G20, G22, G26, and G42 chassis.

Condition: Excellent (A)

$425.95 View part →

2019-2026 BMW 323i Brake Caliper (Used OEM)

Partslink #: OEMG-41715

This brake caliper features a red finish. Fits BMW G20, G22, G23, G26, and G42 chassis.

Condition: Excellent (A)

$449.95 View part →

2012-2019 BMW 323i Front Brake Caliper (Used OEM)

Partslink #: OEMG-44641

It fits vehicles with the B58B30M0 engine. This part is for BMW F30, F32, F33, and F36 chassis vehicles.

Condition: Excellent (A)
Mileage: 130,600 miles

$564.95 View part →

2019-2026 BMW 323i Front Right M Sport Brake Caliper (Used OEM)

Partslink #: OEMG-30072

It is a Brembo brand part with a blue finish. Please ensure compatibility before purchasing as an upgrade. Fits BMW G01 and G20 chassis.

Condition: Excellent (A)

$569.95 View part →

2019-2026 BMW 323i Rear Brake Caliper (Used OEM)

Partslink #: BMA-178358140883

These brake calipers have scratches and scuffs. The parking brake actuators are not included. Please verify your part identification number matches. Fits BMW G42 chassis.

Condition: Excellent (A)

$629.95 View part →

2019-2022 BMW 323i Front Left M Sport Brake Caliper, Blue (Used OEM)

Partslink #: OEMG-32496

This is a set of Brembo brake calipers. There are light paint chips on both calipers. These are blue in color. Fits BMW G01, G02, and G20 chassis.

Condition: Excellent (A)
Mileage: 85,200 miles

$1,163.95 View part →

2019-2026 BMW 323i Brake Caliper Set (Used OEM)

Partslink #: OEMG-38093

This is a complete set of brake calipers. Includes both sides for the front and rear. The calipers are blue. Fits BMW G20, G22, G23, and G26 chassis.

Condition: Excellent (A)

$1,220.95 View part →