2018-2024 Audi S4 Rear Axle Shaft (Used OEM)

Partslink #: OEMG-51508

It includes both sides. Fits Audi B9 chassis.

$69.95 View part →

✓ In Stock

2018-2023 Audi S4 Rear CV Axle Shaft (Used OEM)

Partslink #: OEMG-51509

Includes both sides. Fits Audi B9 chassis.

$69.95 View part →

✓ In Stock

2009-2016 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: OEMG-4510

It shows normal signs of use such as nicks, scuffs, and scratches. Fits Audi 8T chassis.

$83.95 View part →

✓ In Stock

2010-2016 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: OEMG-4511

Fits Audi 8T chassis.

$83.95 View part →

✓ In Stock

2013-2016 Audi S4 Rear CV Axle Shaft (Used OEM)

Partslink #: OEMG-4575

Fits Audi 8T chassis.

$83.95 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.807, Axle Nut Socket Size: 0.945, Axle Nut Thread Size: M14x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 23.425, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 33, Product Condition: New, Shaft Diameter: 1.063, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

24 1/4" Length

$220.01 View part →

✓ In Stock

2004-2008 Audi S4 CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3491206

$144.72 View part →

✓ In Stock

2004-2008 Audi S4 CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3480881

$317.52 View part →

✓ In Stock

2000-2002 Audi S4 CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3438011

25 3/16" Length

$157.64 View part →

✓ In Stock

2004-2009 Audi S4 CV Axle Assembly - Front Left (Metelli)

Partslink #: 17-0693

$332.54 View part →

✓ In Stock

2000-2002 Audi S4 CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3492295

$161.36 View part →

✓ In Stock

2004-2009 Audi S4 CV Axle Assembly - Front Left (GKN Loebro)

Partslink #: 305070

$386.67 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Socket Size: 1.063, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 24.252, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.213, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2004-2009 Audi S4 CV Axle Assembly - Rear Left or Rear Right (Cardone)

Partslink #: 66-7380

$166.43 View part →

ABS Tone Ring Included: No, Axle Nut Included: Yes, Axle Nut Socket Size: 0.748, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Internal Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 18.307, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 42, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2010-2012 Audi S4 CV Axle Assembly - Front Left or Front Right (Cardone)

Partslink #: 66-7418

$187.95 View part →

✓ In Stock

2010-2012 Audi S4 CV Axle Assembly - Rear Left or Rear Right (Autopart International)

Partslink #: W0133-4224382

w/ Torque Vectoring Differential

$203.48 View part →

✓ In Stock

2013-2016 Audi S4 CV Axle Assembly - Rear Right (Autopart International)

Partslink #: W0133-4382820

w/ Torque Vectoring Differential

$292.14 View part →

✓ In Stock

2004-2009 Audi S4 CV Axle Assembly - Front Right (Metelli)

Partslink #: 17-0694

$332.54 View part →

✓ In Stock

2004-2009 Audi S4 CV Axle Assembly - Front Right (GKN Loebro)

Partslink #: 305079

$378.72 View part →

✓ In Stock

2010-2012 Audi S4 CV Axle Assembly - Front Left or Front Right (GKN Loebro)

Partslink #: 304923

$383.22 View part →

✓ In Stock

2018-2025 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: BMA-023147

This CV axle shaft assembly fits Audi RS5, S5, and A5 models. Fits Audi B9 chassis.

$134.95 View part →

✓ In Stock

2018-2023 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: BMA-010444

This is a set that includes both sides. Fits Audi RS5 and S5 chassis.

$159.95 View part →

✓ In Stock

2018-2024 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: BMA-023129

This assembly includes both sides. Fits Audi RS5 and S5 chassis.

$159.95 View part →

✓ In Stock

2018-2022 Audi S4 Front CV Axle Shaft (Used OEM)

Partslink #: OEMG-51657

For vehicles with engine code CWGD. Fits Audi B9 chassis.

$162.95 View part →

✓ In Stock

2018-2023 Audi S4 Front CV Axle Shaft (Used OEM)

Partslink #: OEMG-51660

It fits Audi B9 chassis vehicles.

$162.95 View part →

✓ In Stock

2004-2009 Audi S4 CV Axle Assembly - Rear (Autopart International)

Partslink #: W0133-3443277

$198.29 View part →

✓ In Stock

2018-2021 Audi S4 CV Axle Assembly - Front (Autopart International)

Partslink #: W0133-3492534

$212.30 View part →

✓ In Stock

2018-2024 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: BMA-003725

This set is in working condition but has scratches and scuffs. Please verify your part identification number matches. Fits Audi B9 chassis.

$215.95 View part →

✓ In Stock

2018-2025 Audi S4 CV Axle Shaft (Used OEM)

Partslink #: BMA-003726

This is a set that includes both sides. The parts have scratches and scuffs. Please verify your part number matches.

$215.95 View part →

Audi S4 CV Axle Assembly Replacement

2018-2024 Audi S4 Rear Axle Shaft (Used OEM)

2018-2023 Audi S4 Rear CV Axle Shaft (Used OEM)

2009-2016 Audi S4 CV Axle Shaft (Used OEM)

2010-2016 Audi S4 CV Axle Shaft (Used OEM)

2013-2016 Audi S4 Rear CV Axle Shaft (Used OEM)

2000-2002 Audi S4 CV Axle Assembly - Rear Left or Rear Right (Cardone)

2007-2009 Audi S4 CV Axle Assembly - Front Left (Cardone)

2000-2002 Audi S4 CV Axle Assembly - Front Right (Cardone)

2000-2002 Audi S4 CV Axle Assembly - Front Left (Autopart International)

2007-2009 Audi S4 CV Axle Assembly - Front Right (Cardone)

2000-2002 Audi S4 CV Axle Assembly - Front Left (Autopart International)

2004-2008 Audi S4 CV Axle Assembly - Front Right (Autopart International)

2004-2008 Audi S4 CV Axle Assembly - Front Left (Autopart International)

2000-2002 Audi S4 CV Axle Assembly - Front Right (Autopart International)

2004-2009 Audi S4 CV Axle Assembly - Front Left (Metelli)

2000-2002 Audi S4 CV Axle Assembly - Front Right (Autopart International)

2004-2009 Audi S4 CV Axle Assembly - Front Left (GKN Loebro)

2004-2009 Audi S4 CV Axle Assembly - Rear Left or Rear Right (Cardone)

2010-2012 Audi S4 CV Axle Assembly - Front Left or Front Right (Cardone)

2010-2012 Audi S4 CV Axle Assembly - Rear Left or Rear Right (Autopart International)

2013-2016 Audi S4 CV Axle Assembly - Rear Right (Autopart International)

2004-2009 Audi S4 CV Axle Assembly - Front Right (Metelli)

2004-2009 Audi S4 CV Axle Assembly - Front Right (GKN Loebro)

2010-2012 Audi S4 CV Axle Assembly - Front Left or Front Right (GKN Loebro)

2018-2025 Audi S4 CV Axle Shaft (Used OEM)

2018-2023 Audi S4 CV Axle Shaft (Used OEM)

2018-2024 Audi S4 CV Axle Shaft (Used OEM)

2018-2022 Audi S4 Front CV Axle Shaft (Used OEM)

2018-2023 Audi S4 Front CV Axle Shaft (Used OEM)

2004-2009 Audi S4 CV Axle Assembly - Rear (Autopart International)

2018-2021 Audi S4 CV Axle Assembly - Front (Autopart International)

2018-2024 Audi S4 CV Axle Shaft (Used OEM)

2018-2025 Audi S4 CV Axle Shaft (Used OEM)

What buyers are saying.

Racing Partner Videos

CV Axle Assembly Compatibility for Audi S4

Available Trims

Body Types

Engine Options

Transmissions