2007-2010 Chrysler Sebring Wheel Cover: A Guide to Fitment, Replacement, and Common Issues

Key Compatibility & Identification

The most critical step in replacing this part is ensuring you are buying the correct one. Many Sebring models came with different wheel options from the factory. This specific cover, identified by part numbers like 05272553AC, 🎬 Watch this video to inspect the OEM 16-inch Chrysler Sebring wheel cover. is a 10-spoke design with a silver painted finish. Always verify your wheel diameter, which can be found in the sequence of numbers on your tire's sidewall. A tire size of P215/65R16, for example, indicates a 16-inch wheel.

Symptoms of a Failing Wheel Cover

Failure for a wheel cover is typically related to physical damage or noise, rather than mechanical breakdown.

Noise (Rattling or Clicking)

A rattling or clicking sound from the wheel area that changes with speed can indicate a cracked or loose wheel cover. This happens when a piece of the plastic has broken or when the cover is no longer held tightly against the wheel, allowing it to vibrate during rotation.

Cosmetic Damage

The most common reason for replacement is cosmetic damage. This includes curb rash (scuffs and scrapes from hitting a curb), peeling or faded paint, and cracks from impacts with road debris. While this doesn't affect the vehicle's operation, it detracts from its appearance.

Wheel Cover Has Fallen Off

In rare cases, a severely damaged wheel cover can break apart and fall off the vehicle. This is most often the result of previous damage, such as multiple cracks or broken mounting points around the lug nut holes. It can also happen if lug nuts were not properly torqued after a tire service.

Buying a Used 2007-2010 Sebring Wheel Cover

Purchasing a used OEM (Original Equipment Manufacturer) wheel cover is often the best value, providing a perfect match and factory-grade plastic at a lower cost than a new part from a dealer. Here’s what to check before you buy:

• Check for Cracks: Carefully inspect the entire front and back of the wheel cover, paying close attention to the spokes and the outer rim. Hairline cracks can grow over time and lead to rattling or total failure.
• Inspect the Lug Nut Holes: This is the most critical area. Since these covers are held on by the lug nuts, ensure the plastic around each of the five holes is intact and not cracked or deformed. This area is vital for a secure fit.
• Verify the Finish: Check that the silver paint is in good condition, without major peeling or fading, to ensure it will match the other wheels on your car. Used parts may have minor scuffs, which is often acceptable for a daily driver.
• Confirm the Part Number: If possible, check for an OEM part number on the back of the cover, such as 05272553AB or 05272553AC, to guarantee a perfect match.

Cost of Replacement

The cost for a single 2007-2010 Sebring wheel cover can vary significantly based on the source.

Labor costs for installation are typically zero, as it is a very simple DIY task or is often done for free during a tire rotation or other wheel service.

Installation Guide (Difficulty: 1/5)

Replacing this wheel cover is a straightforward process that requires only a lug wrench. 🎬 See how to quickly replace and install a hubcap on your rim. The estimated time is 15-20 minutes per wheel.

1. Safety First: Park the vehicle on a level surface and engage the parking brake. For added safety, place a wheel chock behind one of the wheels not being worked on.
2. Loosen Lug Nuts: Using the lug wrench from your vehicle's tool kit, slightly loosen (about a half-turn) the five lug nuts on the wheel. Do not remove them yet.
3. Raise the Vehicle: Use your vehicle's jack to lift the corner of the car until the tire is just off the ground. Refer to your owner's manual for proper jack placement.
4. Remove Lug Nuts and Old Cover: Finish unscrewing the five lug nuts and place them in a safe spot. The old wheel cover can now be pulled straight off the wheel studs.
5. Position the New Cover: Align the new wheel cover with the wheel studs. There is a small notch or cutout in the wheel cover that must be aligned with the tire's valve stem. This ensures you can add air to the tire later.
6. Reinstall Lug Nuts: Thread all five lug nuts back on by hand until they are snug. This ensures the wheel cover is centered and held flat.
7. Lower and Torque: Lower the vehicle until the tire is just touching the ground. Use your lug wrench to tighten the lug nuts in a star pattern. Once the car is fully lowered, torque the lug nuts to the manufacturer's specification, which is typically 100 ft-lbs (135 N·m) for this vehicle.

Known Issues, Recalls, and TSBs

There are no recalls or Technical Service Bulletins (TSBs) issued by Chrysler or the NHTSA specifically for the wheel covers on the 2007-2010 Sebring. The most common issue reported by owners is losing a wheel cover, which is almost always due to improper installation (lug nuts not fully tightened) after a tire change or rotation, or from physical damage to the cover's mounting points.

Official Part Numbers

These part numbers are for the same 16-inch, 10-spoke wheel cover. The letters at the end often signify minor updates or revisions over the years, but they are interchangeable.

• 05272553AB
• 05272553AC
• 5272553AB
• 5272553AC

Frequently Asked Questions (FAQ)