2023-2025 Kia Telluride Side Mirror Camera: Fixing BVM Failures & Calibration Issues
This guide covers common failure symptoms, replacement costs, and calibration needs for the camera that powers your Telluride's Blind-Spot View Monitor.
- This part is a CAMERA in the mirror for the Blind-Spot View Monitor (BVM), not the RADAR sensor in the rear bumper.
- Replacement of the camera or the entire mirror assembly REQUIRES professional calibration by a dealer or qualified shop to function correctly.
- Flickering video is a common symptom that may be caused by a bad wiring connection, not necessarily a failed camera.
- When buying a used part, you must match all mirror options (power fold, 360 view, etc.) to ensure compatibility.
Camera vs. Radar Sensor: A Critical Distinction
It is essential to understand the difference between the side mirror camera and the blind spot radar sensor, as they are often confused. They are two separate parts with different functions and locations.
- Side Repeater Camera (This Article): Located in the side mirror housing. It provides the video feed for the Blind-Spot View Monitor (BVM) on your dashboard when you use your turn signal. Part numbers are typically 99230-S9500 (Right/Passenger) and 99220-S9500 (Left/Driver).
- Blind Spot Radar Sensor: Located behind the rear bumper cover on the corners of the vehicle. It powers the Blind-Spot Collision-Avoidance Assist (BCA) and Rear Cross-Traffic Collision-Avoidance Assist (RCCA) systems, triggering the warning light in your mirror. A common part number for the right side is 99150-S9050.
This guide focuses exclusively on the Side Repeater Camera located in the mirrors.
Symptoms of a Failing Side Mirror Camera
When the side camera begins to fail, you will lose some or all of the functionality of the Blind-Spot View Monitor. Here are the most common symptoms:
- Black or Blank Screen: The most obvious sign of failure. When you activate the turn signal, the instrument cluster display where the video feed should appear remains black or shows no image.
- Flickering or Scrambled Video: The camera feed may appear intermittently, flicker, or show distorted lines. This can be caused by a failing camera or a poor electrical connection. A Technical Service Bulletin (TSB) for earlier models pointed to faulty coaxial cable terminals causing this exact issue.
- "Blind Spot System Disabled" Warning: A fault in one of the cameras can trigger a warning message on the dashboard, disabling the entire BVM system.
- Distorted or Misaligned Image: The camera view may appear warped, blurry, or misaligned, making the 360° Surround View Monitor (if equipped) unusable for parking. This often points to a physical misalignment or a need for calibration.
- Poor Low-Light Performance: While some degradation is normal at night, a failing camera may become completely unusable in low-light conditions, showing a grainy or black image.
Pro Tip: Before assuming the camera is broken, thoroughly clean the lens on the underside of the mirror with a soft, damp cloth. Dirt, road salt, or debris on the lens is a common cause of a blurry or obstructed image.
Known Issues, TSBs, and Recalls
As of mid-2026, there are no active recalls specifically for the side mirror cameras on the 2023-2025 Kia Telluride. However, several recalls exist for other issues like power seats, exterior trim, and airbags.
A notable Technical Service Bulletin (TSB) for 2020-2021 models, TSB ELE233, addressed flickering or lined camera images caused by poor terminal connections in the coaxial camera cable. While this TSB is not for the 2023-2025 model years, the underlying issue of a loose connection causing video problems is a valuable diagnostic tip for any flickering camera issue.
Warning: Replacement of the side mirror camera or the entire mirror assembly requires a calibration procedure to ensure the Blind-Spot View Monitor and Surround View Monitor systems function correctly. This procedure must be performed by a dealership or a qualified shop with the proper tools and software.
Buying a Used Side Repeater Camera
Given the high cost of a new OEM camera, a used unit from a reputable recycler is an excellent value. Because these are complex electronic components integrated into the vehicle's safety systems, cheap aftermarket alternatives are not available or recommended. Here’s what to look for when buying used:
- Verify Compatibility: The camera itself is often sold as part of the complete mirror assembly. Telluride mirrors have many variations: power-folding, Surround View Monitor support, memory function, and different color caps (glossy vs. matte black). Ensure the used assembly you buy has the exact same features as your original mirror. The safest bet is to match the part number from your original mirror.
- Inspect the Lens: Check the small camera lens on the bottom of the mirror housing for deep scratches, hazing, or cracks. Minor surface scuffs are okay, but significant damage will permanently degrade image quality.
- Check the Connector: Look at the electrical connector on the camera or mirror assembly. The pins should be straight, clean, and free of any green or white corrosion. Damaged pins are a major red flag.
- Source Vehicle Information: If possible, get the mileage and VIN of the vehicle the part came from. A lower-mileage part is always preferable. Ask about any collision damage to ensure the mirror and camera were not impacted.
Cost Comparison
Prices can vary based on your location and the specific mirror options on your Telluride. The camera is available separately but is often replaced as part of the entire mirror assembly.
| Part or Service | Estimated Cost |
|---|---|
| New OEM Camera Only | $450 - $680 |
| New OEM Mirror Assembly | $460 - $1,500+ (depending on options) |
| Used OEM Camera/Mirror | $100 - $350 |
| Shop Labor (Replacement & Calibration) | $150 - $400 |
Replacement & Calibration
Replacing the side mirror assembly is a moderately easy job for a DIYer, but the required calibration makes it a job best left to professionals.
- Difficulty: 2 out of 5 for physical replacement; 5 out of 5 for required calibration.
- Process: The basic steps involve removing the interior door trim panel (the triangular piece opposite the mirror), disconnecting the electrical harness, and unbolting the mirror assembly from the door. Installation is the reverse of removal.
- Calibration: After installation, the new camera MUST be calibrated. According to I-CAR repair procedures, calibration is required anytime the camera or the mirror it's attached to is removed or replaced. This process uses special mats and a diagnostic scan tool to align the camera's view with the vehicle's position, ensuring the BVM and 360° view are accurate. Failure to calibrate can result in a distorted image and incorrect blind spot display.
Part Numbers & Technical Specifications
| Part Name | Side | Part Number | Notes |
|---|---|---|---|
| Camera Assembly, Side View | Right (Passenger) | 99230-S9500 | Fits 2023-2025 Telluride. |
| Camera Assembly, Side View | Left (Driver) | 99220-S9500 | Fits 2023-2025 Telluride. |
| Blind Spot Radar Sensor | Right (Passenger) | 99150-S9050 | Different part. Located in rear bumper. |
Frequently Asked Questions
Is the side mirror camera the same as the blind spot sensor?
No. The camera is in the mirror and provides a video feed to your dashboard (Blind-Spot View Monitor). The blind spot sensor is a radar unit in the rear bumper that detects cars and activates a warning light in your mirror (Blind-Spot Collision-Avoidance Assist).
Do I have to get the new camera calibrated?
Yes. Any time the side mirror camera or the entire mirror assembly is removed or replaced, a calibration procedure is required. This ensures the camera view is accurate for both the Blind-Spot View Monitor and the 360° Surround View Monitor. This must be done by a dealer or qualified shop.
Can I just replace the camera instead of the whole mirror?
Yes, the camera is sold as a separate part (e.g., 99230-S9500). However, replacing it requires disassembling the mirror housing, which can be delicate work. Often, it is simpler and sometimes more cost-effective to replace the entire mirror assembly, especially when buying a used part.
Why is my camera view flickering or showing lines?
While this could be a sign of a failing camera, it is often caused by a poor electrical connection. A Kia TSB for earlier models identified this exact problem, tracing it to loose terminals in the camera's coaxial cable. Before replacing the camera, it's worth having the wiring and connectors inspected.
Technical Specifications
OEM Part Numbers: 99230-S9500 (Right/Passenger Side Camera) 99220-S9500 (Left/Driver Side Camera)
Integrates with Blind-Spot View Monitor (BVM) and Surround View Monitor (SVM) systems. Requires professional calibration after installation.
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Kia Telluride: