2013-2014 SRT Viper Windshield Washer Pump Guide
A clear windshield is critical in a Viper; here’s how to fix a washer system that has stopped spraying.
- A failed washer pump is a safety issue that compromises visibility; symptoms include no spray or a very weak spray.
- An aftermarket replacement pump is a cost-effective and reliable solution for the SRT Viper.
- DIY replacement is straightforward, typically taking about an hour with basic hand tools.
- Always check the fuse, fluid level, and for clogged nozzles before condemning the pump.
Is Your Viper's Washer Pump Failing?
A broken washer pump is more than a minor annoyance—it's a safety hazard, especially in poor weather. The signs of failure are usually obvious. If you activate the washers and nothing happens, the pump is a likely culprit. Before assuming the pump is bad, make sure you have fluid in the reservoir and check that the nozzles on the hood aren't clogged with wax or debris, which can often be cleared with a small pin.
Symptoms of a Bad Washer Pump
- No Spray at All: You activate the switch, the wipers move, but no fluid comes out. You may or may not hear the pump motor hum.
- Weak or Inconsistent Spray: The fluid barely reaches the windshield or comes out in a weak dribble, failing to clean the glass effectively. This can indicate a dying motor.
- Pump Motor is Silent: If you hear absolutely nothing when you try to use the washers, it could be a dead pump or an electrical issue like a blown fuse.
- Pump Runs, No Fluid Sprays: If you can hear the pump motor running, the issue might be an internal failure in the pump, a disconnected hose, or a clog in the system's filter.
Pro Tip: Check the Easy Stuff First
Before you order a new pump, always check the washer system fuse and ensure the fluid reservoir is full. Sometimes, a hose can pop off its connector, which is an easy fix. Following these simple diagnostic steps can save you time and money.
OEM vs. Aftermarket Replacement Pumps
When replacing a simple component like the washer pump on your SRT Viper, you have two main choices: a new OEM (Original Equipment Manufacturer) part from a Dodge dealer or a new aftermarket part. The OEM part is identical to the one your car was built with, but it comes at a premium price. For a part like a washer pump, an aftermarket 'Replacement' brand part offers a significant cost saving without a noticeable difference in performance or longevity. These parts are designed to be direct-fit replacements, making installation straightforward.
Washer Pump Replacement Cost for 2013-2014 SRT Viper
| Part Type | Estimated Cost |
|---|---|
| New Aftermarket | $25.03 |
| New OEM (Mopar) | $30 - $142 |
| Shop Labor | $110 - $161 |
Known Issues, Recalls, and Service Bulletins
There are no specific recalls or technical service bulletins (TSBs) from NHTSA for the washer pump on the 2013-2014 SRT Viper. However, a recall (NHTSA 16V-813) was issued for some 2016 Dodge Darts where a faulty washer pump could create a voltage spike and damage the Body Control Module (BCM), disabling the wipers. While the Viper was not included in this recall, it highlights the importance of ensuring any replacement part functions correctly to avoid potential electrical complications.
Frequently Asked Questions (FAQ)
Where is the washer pump located on the 2013-2014 SRT Viper?
The washer pump is located at the bottom of the washer fluid reservoir. To access it, you will typically need to jack up the front passenger side of the vehicle, remove the wheel, and then remove the plastic fender liner to expose the reservoir and pump.
Is replacing the washer pump a difficult DIY job?
No, this is a very feasible DIY task for someone with basic tools. The job involves draining the fluid, disconnecting a hose and an electrical connector, and pulling the old pump out of its rubber grommet. The new pump pushes right back in.
What tools are needed to replace the washer pump?
You will need a jack and jack stands, a lug wrench for the wheel, a drain pan for the fluid, and likely some basic screwdrivers or trim removal tools to detach the fender liner clips.
Is an aftermarket washer pump a reliable choice for my Viper?
Yes. For a straightforward component like a washer pump, a quality aftermarket part provides the same function as an OEM part at a much lower cost, making it a smart and reliable repair choice.
Technical Specifications
OEM Part Numbers: 68164356AA 68164356AB 5103452AA
Direct-fit electric pump, typically includes new rubber grommet.
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- SRT Viper: