Chrysler Intrepid Windshield Washer Pump Replacement Guide (1999-2004)
A non-working washer pump is a safety hazard; here’s what you need to know to fix it.
- A failed washer pump is a safety issue; replacement is simple and affordable.
- Diagnose the problem first: a humming sound often points to a clog, while silence could be a fuse or a dead pump.
- The pump is located behind the passenger-side wheel well liner and is an easy DIY job for most owners.
- Aftermarket pumps offer excellent value compared to the much more expensive OEM Mopar part for this vehicle.
Is Your Intrepid's Washer Pump Failing?
A broken windshield washer pump can be a major safety problem, especially in bad weather. On the 1999-2004 Chrysler Intrepid, the washer pump is a common part to fail, but it is also inexpensive and simple to replace. The signs of a bad pump are usually easy to spot.
Diagnosing the Problem
Before you buy a new pump, make sure the pump is actually the problem. Sometimes, other issues can stop the fluid from spraying.
- Pump makes a humming sound, but no fluid sprays: This often means the pump's motor is working, but the fluid is blocked. First, try cleaning the small spray nozzles on the hood with a pin. If that doesn't work, the pump itself might be clogged or its internal parts may have failed.
- No sound at all when you activate the washer: This could mean the pump has failed completely. However, you should first check the fuse for the washer system. On some Intrepids, this fuse is located in the panel on the driver's side of the dashboard.
- Washer fluid leaking: If you see a puddle of washer fluid under the front passenger side of the car, the pump's housing may be cracked or the rubber seal where it enters the tank has gone bad.
Pro Tip: Check for Clogs First
If you can hear the pump running, disconnect the fluid hose right at the pump. Activate the washer switch for a moment. If fluid squirts out, your pump is good and the blockage is in the hoses or nozzles. If no fluid comes out, the pump needs to be replaced.
Choosing a New Aftermarket Washer Pump
For a simple part like a washer pump, an aftermarket replacement is a smart choice for most Intrepid owners. The original Mopar pump can be very expensive, while an aftermarket pump provides the same function for a fraction of the cost. Brands like Replacement, Trico, and others offer reliable pumps that fit and work like the original. Since the job is easy, paying extra for an OEM part doesn't provide much benefit.
| Part Type | Part Cost | Shop Labor Cost | Total Estimated Cost |
|---|---|---|---|
| New Aftermarket | $15 - $35 | $62 - $92 | $77 - $127 |
| New OEM (Mopar) | $140 - $150 | $62 - $92 | $202 - $242 |
Cost estimates are based on national averages for parts and labor and may vary by location.
Replacing the Washer Pump
This is a beginner-friendly repair that you can do yourself in under an hour with basic tools. The washer pump is located at the bottom of the washer fluid reservoir. You can get to it by removing a few clips or screws from the splash shield in the front passenger-side wheel well and pulling it back. The pump is just pressed into a rubber grommet and can be pulled straight out.
Known Issues
While searches for official recalls and Technical Service Bulletins (TSBs) for the 1999-2004 Intrepid's washer pump came up empty, some other Chrysler vehicles have had recalls where a faulty washer pump could cause a voltage spike and damage the Body Control Module (BCM), leading to wiper failure. This is not a documented issue for this specific Intrepid model, but it highlights the importance of using a quality part.
Frequently Asked Questions
Where is the washer pump on a 1999-2004 Chrysler Intrepid?
The washer pump is at the bottom of the washer fluid reservoir. It is accessed by pulling back the plastic liner in the front passenger-side wheel well.
Is it hard to replace the washer pump yourself?
No, this is considered an easy DIY job. It requires basic hand tools and usually takes less than an hour. You do not need to remove the entire reservoir.
Why does my new pump not spray?
First, make sure the fluid reservoir is full. Second, check that the electrical connector is plugged in securely. If you can hear the pump run, you may have a clog in the lines or nozzles that needs to be cleared.
Do I need to drain the washer fluid to replace the pump?
Yes. When you pull the old pump out of the reservoir, all the fluid will drain out. Have a bucket ready to catch it so you can reuse it or dispose of it properly.
Technical Specifications
OEM Part Numbers: 5103452AA 5011807AB 5013056AA 5015938AA 5017795AA 55077241AA 55077241AB
12V DC motor, 2-pin electrical connector, single fluid outlet port.
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Chrysler Intrepid: