2022-2025 Audi Q4 e-tron & Sportback Overhead Map Light: Touch Controls and Electrical Issues
This guide covers common symptoms, replacement, and what to check when buying a used overhead map light console for your 2022-2025 Audi Q4 e-tron or Q4 e-tron Sportback.
- This part is a simple, plug-and-play replacement that does not require programming.
- Failures are typically electronic, causing flickering or unresponsive touch controls, not burnt-out bulbs.
- While no recalls exist for this part, a TSB for the HVAC controls shows similar flickering issues can be caused by vehicle network problems.
- When buying used, the most important thing is to match the part number and color code (e.g., 11A947290A4PK for black).
Symptoms of a Failing Map Light Console
While widespread failures on the 2022-2025 Audi Q4 e-tron are not yet commonly reported, issues with this type of touch-sensitive module on other Audi models can point to potential future problems. Symptoms are often electrical or behavioral rather than a simple burned-out bulb, as these consoles use long-lasting LEDs.
- Unresponsive Touch Controls: The lights do not respond when you touch the control surfaces. This can be intermittent or a complete failure.
- Flickering Lights: The LED lights may flicker or pulse randomly. This can be caused by an internal fault in the console's electronics or a communication issue on the vehicle's data bus.
- Lights Stay On or Won't Turn Off: A faulty control module might fail to turn the lights off, leading to a slow drain on the vehicle's 12-volt battery.
- Ghosting or Random Activation: The lights may turn on and off by themselves without any input. This is a known issue on other Audi models with similar touch-sensitive dome lights and can be caused by sensitivity issues or internal electronic faults.
Pro Tip: Before assuming the map light console is faulty, ensure the vehicle's 12-volt battery is in good health. Low voltage can cause unpredictable behavior in various electronic modules throughout the car.
Known Issues, TSBs, and Recalls
As of mid-2024, there are no specific recalls or Technical Service Bulletins (TSBs) for the overhead map light console on the 2022-2025 Audi Q4 e-tron or Q4 e-tron Sportback.
However, Audi has issued a TSB for a similar issue on a different part that is highly relevant. TSB 87 23 58 2071176/2 addresses an issue where the lighting for the HVAC control head flickers intermittently, and the controls become unresponsive. The cause is noted as a communication error on the LIN bus network. Since the overhead light console also communicates on this network, it is possible that similar software or communication glitches could cause flickering or unresponsiveness in the map lights. A key cycle (turning the vehicle off and on again) may temporarily restore function.
Buying a Used Map Light Console
A used OEM map light is an excellent, cost-effective replacement. Since the part is largely cosmetic and electronic, there are a few key things to check before buying.
- Verify the Part Number: The most important step. The base part number is 11A947290A. The suffix indicates the color. For example, 11A947290A4PK is the part number for the black version. Check the number on your original part to ensure a perfect match.
- Inspect the Lens and Housing: Look for deep scratches, cracks, or discoloration on the plastic lens and surrounding housing. Check for any signs of heat damage or melting, which would indicate a severe internal failure.
- Check Mounting Tabs: These consoles are held in by plastic or metal clips. Ensure all clips and mounting points are intact and not broken or bent. A unit with broken tabs will not sit securely in the headliner and may rattle.
- Examine the Electrical Connector: Look at the connector port on the back of the unit. Make sure it is clean, free of corrosion, and that none ofthe pins are bent or pushed in.
Cost Comparison
Replacing the map light console is an affordable repair, especially when using a recycled OEM part.
| Part Type | Estimated Cost |
|---|---|
| New OEM | $35 - $50 |
| Used OEM | $15 - $30 |
| New Aftermarket | Not commonly available |
| Shop Labor | $25 - $50 (0.2-0.3 hours) |
Replacement Guide (DIY)
Replacing the overhead map light console is a straightforward job that most DIYers can complete in under 15 minutes.
- Difficulty: 1/5 (Very Easy)
- Estimated Time: 0.2 hours
- Tools Needed: Plastic trim removal tool (pry tool)
Warning: Always use a plastic pry tool, not a screwdriver. A metal tool will easily scratch the plastic console and damage the soft headliner material.
Step-by-Step Procedure:
- Find the seam between the overhead console and the headliner.
- Carefully insert a plastic pry tool into the seam, typically starting from the edge closest to the windshield.
- Gently pry downwards. The console is held in by several pressure clips. You will hear them pop as they release. Work your way around the console.
- Once the console is loose, lower it carefully. It will still be connected by one or more electrical harnesses.
- Depress the locking tab on the electrical connector(s) and pull it straight out to disconnect the console.
- To install the new unit, simply plug in the electrical connector, align the console with the opening in the headliner, and press firmly upwards until all the clips snap securely into place.
- Test the lights to confirm proper operation.
Frequently Asked Questions
Do I need to program a new map light console?
No. This part is typically plug-and-play and does not require any special programming or calibration after installation.
Why are my touch-sensitive lights acting weird after cleaning the car?
Moisture or residue from cleaning products on the touch surfaces can interfere with the capacitive sensors, causing them to activate randomly or not respond. Ensure the surface is clean and completely dry.
Is the map light the same for the Q4 e-tron and the Q4 e-tron Sportback?
Yes, the 2022-2025 Audi Q4 e-tron and Q4 e-tron Sportback share the same overhead map light console as they are built on the same platform.
Can I just replace the LED bulb?
No. The LEDs are integrated directly into the circuit board of the console. If a light fails, the entire assembly must be replaced.
Technical Specifications
OEM Part Numbers: 11A947290A 11A947290A4PK 11A947290ADK1
Uses integrated LED lighting and capacitive touch controls. Communicates via the vehicle's LIN bus network.
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Audi Q4 e-tron:
- Audi Q4 e-tron Sportback: