2021-2025 Genesis GV80 3rd Row Cup Holder: Fitment, High Cost, and Replacement
This is the definitive guide to diagnosing, buying, and replacing the surprisingly complex and expensive third-row cup holder assembly in 7-passenger GV80 models.
- This part ONLY fits 7-passenger Genesis GV80 models; it will not fit the 5-passenger version.
- A new OEM replacement is extremely expensive (often over $500), making a quality used OEM part the most logical choice.
- Replacement is moderately difficult (3/5) as it requires removing the entire rear quarter trim panel.
- When buying used, physically inspect for intact mounting tabs and a smoothly operating door mechanism.
Key Compatibility Warning
Warning: These third-row cup holder assemblies are only compatible with 2021-2025 Genesis GV80 models originally equipped with 7-passenger (3rd row) seating. They will not fit 5-passenger models, as the entire rear quarter panel trim is different. Always verify the vehicle's original seating configuration before purchasing.
Symptoms of a Failing 3rd Row Cup Holder
Since this is not an electronic part, failures are purely mechanical or cosmetic. There are no known widespread issues, but given its location and use, damage can occur. Look for the following symptoms:
- Broken or Jammed Door: The cover may refuse to open, stay shut, or flap loosely due to a broken spring or hinge mechanism.
- Rattling Noises: A common sign of a loose or broken part is a rattling or buzzing sound coming from the rear quarter panel area while driving. This can happen if the cup holder's mounting tabs have cracked or if internal components have broken free.
- Sticky Operation: Spilled drinks can gum up the internal mechanism, making the door difficult to open or close smoothly.
- Visible Cracks: Physical impact from cargo or passengers can cause the plastic housing or faceplate to crack, compromising its ability to hold drinks securely and affecting the interior's appearance.
Buying a Used GV80 3rd Row Cup Holder
Given the exceptionally high cost of a new OEM replacement, a used part is the most practical and economical choice for this repair. Aftermarket versions for this specific, integrated part are not available. Here’s what to inspect before buying a recycled OEM cup holder:
- Test the Mechanism: If possible, operate the cup holder door several times. It should open and close smoothly with proper tension. A lazy or sticky door suggests a worn-out spring or residue from spills.
- Inspect All Mounting Points: Carefully check the back of the assembly for any broken or cracked plastic mounting tabs. These are critical for a secure, rattle-free installation. Even one broken tab can cause problems.
- Check for Cracks and Scratches: Examine the entire unit, especially the front face, for any cracks, deep scratches, or stress marks in the plastic.
- Verify the Part and Color Number: The most common part number is 85747-T6500-UBL for the right (passenger) side. The 'UBL' suffix indicates the color code. Ensure the part you are buying matches your vehicle's interior color.
Pro Tip: A used OEM cup holder that is fully functional is a far better value than paying dealership prices, which can be over $500 for the new part alone. Since it's a non-wear item, a clean, undamaged used part will perform identically to a new one.
Known Issues, TSBs, and Recalls
As of mid-2026, there are no specific recalls or Technical Service Bulletins (TSBs) from Genesis or the NHTSA that relate to the third-row cup holders in the 2021-2025 GV80. While the vehicle has had recalls for issues like fuel pipes and instrument panel software, none affect this interior trim component.
Cost Comparison
The cost of this part highlights the value of choosing a used OEM component.
| Part Type | Estimated Cost | Notes |
|---|---|---|
| New OEM | $575 - $830 | Extremely expensive for a plastic assembly. Price varies by dealership. |
| Used OEM | $150 - $300 | The most cost-effective solution. Price depends on condition and availability. |
| New Aftermarket | Not Available | Due to the complexity and specific fitment, aftermarket manufacturers do not produce this part. |
| Shop Labor | $150 - $300 | Expect 1.5 to 2.5 hours of labor for a professional to remove the quarter panel trim and replace the unit. |
Installation Overview & Difficulty
- Difficulty Rating: 3 out of 5 (Moderate)
- Estimated Time: 1.5 - 2.5 hours
- DIY Feasible: Yes, for a patient and careful individual.
Replacing this cup holder is more involved than it appears because it requires the removal of the entire rear quarter trim panel. While no special tools are needed, a set of plastic trim removal tools is highly recommended to avoid scratching panels or breaking clips.
The general steps are as follows:
- Disconnect the Battery: As a precaution, disconnect the negative battery terminal, as you may be working near wiring for speakers or power outlets.
- Remove Adjacent Trim: You will likely need to remove the rear door scuff plate and potentially fold down or remove the third-row seats to gain access.
- Remove the Quarter Panel: Locate and remove any visible screws, which may be hidden behind small plastic covers. Then, using trim removal tools, carefully pry the panel away from the vehicle body to release the hidden retaining clips. Start from a bottom edge and work your way around.
- Disconnect Electrical Components: The panel may have wires connected for speakers or power outlets. Carefully disconnect these before fully removing the panel.
- Swap the Cup Holder: With the panel removed and placed on a soft surface, you can access the screws or clips holding the cup holder assembly in place from the back. Unscrew the old unit and install the new one.
- Reassembly: Reconnect any electrical connectors, align the panel's clips with the holes in the body, and press firmly to snap it back into place. Reinstall all screws and adjacent trim pieces.
Technical Specifications & Part Numbers
The primary part number identified is for the right-hand (passenger side) assembly.
| Specification | Value |
|---|---|
| Part Name | Tray Assembly Luggage Side Right-hand, Armrest |
| Right Side OEM Part Number | 85747-T6500-UBL |
| Left Side OEM Part Number | 85746-T6500-UBL (inferred) |
| Color Code | UBL (confirm with seller) |
| Fitment Years | 2021, 2022, 2023, 2024, 2025 |
| Required Vehicle Option | 7-Passenger Seating (3rd Row) |
Frequently Asked Questions (FAQ)
Will this cup holder fit my 5-passenger GV80?
No. The quarter panel trim and underlying structure of the 5-passenger models are completely different. This part is exclusively for GV80s with a factory-installed third row.
Is this part sold as a pair for the left and right sides?
No, they are sold individually. The part number 85747-T6500-UBL is specifically for the right (passenger) side. The left side would have a corresponding, different part number (likely 85746-T6500-UBL).
Why is the new OEM part so expensive?
The high price is due to it being a large, vehicle-specific, and relatively complex assembly rather than a simple universal part. It is often considered part of the main side panel, which drives up the cost. The MSRP from Genesis dealers can be over $800.
Can I just fix my broken cup holder door instead of replacing the whole thing?
It is unlikely. The internal spring and hinge mechanisms are generally not sold as separate components. If the plastic housing or hinge points are cracked, a full replacement is the only reliable repair.
Technical Specifications
OEM Part Numbers: 85747-T6500-UBL 65747T6500
Position: Right (Passenger) Side, Luggage Area. For vehicles with 3rd-row seating ONLY.
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Genesis GV80: