2018-2020 Jaguar E-PACE Instrument Panel Bezel: Solving Rattles and Part Number Confusion
This guide clarifies common rattles and decodes the critical difference between the instrument bezel and the overhead console part numbers.
- The most common failure is rattling, caused by broken plastic mounting clips.
- A warning about panoramic vs. standard roofs applies to the OVERHEAD CONSOLE (part T2H24337PVJ), NOT the instrument panel bezel.
- When buying used, inspect every mounting tab on the back of the part; even one broken tab can cause rattles.
- This is a DIY-friendly repair that requires plastic trim tools and about an hour of time.
Symptoms of a Failing Instrument Panel Bezel
Since the instrument panel bezel is a cosmetic trim piece, its failure is typically related to physical condition and noise rather than electronic or mechanical breakdown. There are no OBD-II codes associated with this part.
- Rattling or Creaking Noises: This is the most common complaint. Noises that sound like they are coming from behind the steering wheel or from within the dashboard, especially when driving over rough roads, can often be traced to a loose bezel. This is usually caused by failed or broken plastic mounting clips that can no longer hold the bezel tightly against the dashboard.
- Visible Cosmetic Damage: Scratches, scuffs, or peeling of the soft-touch or metallic finish are clear signs of wear. Damage can occur from cleaning with harsh chemicals or from accidental impact.
- Cracks: The plastic can become brittle over time and develop stress cracks, especially around the clip locations or screw holes. This is more common in vehicles exposed to extreme temperature swings.
- Poor Fitment: You may notice visible gaps between the bezel and the surrounding dashboard panels. This indicates that the bezel is not seated correctly, likely due to broken clips or improper installation.
CRITICAL WARNING: Part Number Confusion & Roof Type
You may find information linking a dashboard part to whether the E-PACE has a standard metal roof or a panoramic glass roof. This warning applies to the Overhead Console (the part on the ceiling with lights and switches), NOT the instrument panel bezel.
The part number T2H24337PVJ is for the overhead console for models WITHOUT a panoramic roof. The panoramic roof requires a different console to house the sunblind controls. The instrument panel bezel on the dashboard is not affected by the roof type. Do not use the roof type to determine which instrument panel bezel you need.
Buying a Used 2018-2020 E-PACE Instrument Panel Bezel
A used OEM bezel is an excellent choice, as it guarantees perfect fitment, which is crucial for preventing rattles. Aftermarket structural replacements are generally not available for this part, only stick-on cosmetic covers. Here’s what to check before you buy.
1. Inspect All Mounting Tabs
This is the most critical inspection point. Turn the bezel over and carefully examine every single plastic tab and clip receiver. They should all be present, intact, and free of stress marks or cracks. Even one broken tab can prevent the bezel from sitting flush and will likely lead to the same rattles you are trying to fix.
2. Check for Cosmetic Damage
Thoroughly inspect the front surface under good lighting. Look for deep scratches, peeling of the finish, and any discoloration. Be aware that sellers often use cleaning products that can temporarily hide blemishes, so ask for photos from multiple angles. Used parts are sold as-is, and color matching is not guaranteed.
3. Verify the Part Number (If Possible)
If you have already removed your old bezel, the part number should be stamped on the back. Match it to the used part you intend to buy. The primary OEM part number for the bezel appears to be JK83519A58. Do not be confused by other numbers for different dashboard components.
Replacement Overview & Difficulty
Replacing the instrument panel bezel is a relatively straightforward DIY job for most people with basic tools.
- Difficulty: 2 out of 5
- Time: 30-60 minutes
- Tools Needed: Plastic trim removal tools, small pick or flathead screwdriver, possibly a Torx driver.
General Steps:
- To give yourself more room, adjust the steering wheel to its lowest and most extended position.
- Use plastic trim removal tools to carefully pry the bezel away from the dashboard. Never use metal screwdrivers, as they will damage the soft-touch dash material.
- Start at one edge and work your way around, releasing the clips one by one. There may be a hidden screw at the top or bottom, sometimes concealed by a small cover.
- Once all clips and screws are released, the bezel will pull away.
- Installation is the reverse of removal. Line up the clips, and press the new bezel firmly into place until it clicks and sits flush with the dashboard.
Pro Tip: Before installing the new bezel, consider applying small pieces of felt or foam tape to the contact points on the back of the bezel where it touches the dashboard. This is a common dealer fix for persistent rattles and can provide extra insurance against future noise.
Cost Comparison
Prices can vary, but this table provides a general estimate for the 2018-2020 E-PACE instrument panel bezel.
| Part Type | Estimated Cost |
|---|---|
| New OEM | $120 - $200 (estimated from dealer sites for similar trim) |
| Used OEM | $40 - $75 |
| New Aftermarket | Not Available (only cosmetic overlays) |
| Shop Labor | $100 - $200 (based on 1 hr at standard shop rates) |
Frequently Asked Questions (FAQ)
Does the instrument panel bezel change if my E-PACE has a panoramic roof?
No. The instrument panel bezel is the same for all roof types. The compatibility warning about roof types applies to the overhead console on the ceiling, not the trim around your speedometer.
My bezel isn't broken. Can I just fix the rattle?
Yes, in many cases. If the rattle is caused by loose fitment and not a completely broken clip, you can often fix it. Carefully remove the bezel and apply felt tape or small foam pads to the clips and contact points on the back of the bezel. This will tighten the fit and dampen vibrations when you reinstall it.
Is replacing the instrument panel bezel a difficult DIY job?
No, it is considered a beginner-friendly task. The key is to use proper plastic trim removal tools to avoid damaging your dashboard and to have patience when releasing the clips. The entire process should take less than an hour.
Why are all the mounting tabs so important on a used bezel?
The bezel is held in place entirely by pressure from its clips and tabs. If even one is broken, it creates a weak point that will not be held tightly against the dashboard. This small amount of play is all that is needed to cause a persistent and annoying rattle, defeating the purpose of the replacement.
Technical Specifications
OEM Part Numbers: JK83519A58 T2H24337PVJ (This is for the Overhead Console, often confused with this part)
Molded ABS plastic construction. Secured by integrated clips and potentially screws.
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Jaguar E-PACE: