2010-2011 Honda Insight Grille: Decoding Color Codes and Fitment
This guide details the specific part numbers, color variations, and replacement challenges for the 2010-2011 Honda Insight front grille.
- This grille only fits 2010-2011 Honda Insight models; it is not compatible with the 2012 facelift version.
- When buying a used grille, the most critical inspection is for broken mounting tabs on the back.
- The grille was available with two different silver trim moldings: Light Silver (NH757M) and Medium Silver (NH766M). Verify your color before buying.
- Replacement requires removing the entire front bumper cover, which is a manageable DIY task for most.
Symptoms of a Damaged Grille
Failure of the front grille is almost always due to physical damage rather than a mechanical fault. The symptoms are typically straightforward and visible.
- Visible Cracks or Holes: The most common symptom is damage from impacts with road debris, animals, or minor parking lot collisions. This can range from small starburst cracks to large, broken-out sections.
- Faded or Peeling Finish: Over time, exposure to UV rays and weather can cause the painted or chrome-like trim pieces to fade, peel, or become cloudy. This is a cosmetic issue but can detract from the vehicle's appearance.
- Loose Fitment or Rattling: The grille is held in place by a series of plastic tabs and clips. If these tabs break, the grille can become loose, creating a rattling noise while driving or showing a noticeable gap between it and the bumper cover.
Warning: A severely damaged or loose grille could detach from the vehicle at speed, creating a hazard for other drivers. It's best to secure or replace it promptly if any mounting points are broken.
Known Issues, Recalls, and TSBs
As of mid-2026, there are no recalls or Technical Service Bulletins (TSBs) issued by Honda or the NHTSA specifically for the grille on the 2010-2011 Honda Insight. Any issues with this part are related to wear, tear, and physical damage rather than a manufacturing defect.
Buying a Used 2010-2011 Insight Grille
A used OEM grille is often a great value compared to a new part from the dealer. However, careful inspection is key to getting a good part.
1. Confirm Compatibility: 2010-2011 ONLY
The single most important check is the model year. The grille for the 2010-2011 Insight is unique and will not fit 2012-2014 models. The 2012 facelift introduced a different bumper and a grille with a more prominent, wider chrome bar. Always confirm the donor vehicle's year before purchasing.
2. Inspect All Mounting Tabs
This is the most critical inspection point for a used grille. The grille attaches to the inside of the front bumper cover with several plastic tabs and screws. These tabs are brittle and often break during removal. Carefully flip the grille over and inspect every single tab for stress marks (white discoloration) or clean breaks. Even one or two broken tabs can result in a poor fit and rattling.
3. Check for Hidden Cracks
Look for more than just obvious holes. Examine the entire surface, especially around the mounting points and the area where the emblem sits, for hairline cracks. Flex the grille slightly to see if any small cracks open up.
4. Verify the Trim Color
The 2010-2011 Insight grille came with two different silver trim moldings. It is crucial to match the color to your original part for a correct appearance.
- Light Silver Metallic (NH757M): Part number 71122-TM8-A01ZA.
- Medium Silver Metallic (NH766M): Part number 71122-TM8-A01ZC.
5. Emblem and Accessories
Check if the grille comes with the Honda "H" emblem. This is often sold separately and can be costly to buy new. The OEM part number for the emblem is 75701-TF0-003 (which was later superseded by 75701-TF0-010). If the used grille includes a clean, undamaged emblem, it adds significant value.
Pro Tip: Choosing a used OEM grille over a cheap aftermarket one is highly recommended. OEM parts are made from higher-quality plastics that resist fading and fit perfectly, whereas aftermarket grilles often have flimsy mounting tabs that break easily and may not align correctly with the bumper and hood.
Cost Comparison
Prices for a 2010-2011 Honda Insight grille can vary significantly based on the source and condition.
| Part Type | Estimated Cost | Notes |
|---|---|---|
| New OEM | $350 - $530 | Includes the base grille and one of the silver moldings, purchased separately. Emblem is extra. |
| New Aftermarket | $70 - $120 | Quality and fit can be inconsistent. May not include trim pieces. |
| Used OEM | $100 - $250 | Price depends heavily on condition, color, and whether the emblem is included. |
| Shop Labor | $100 - $200 | Typically 1-1.5 hours of labor. Requires removal of the front bumper cover. |
Replacement Overview
Replacing the grille on a 2010-2011 Insight is a manageable DIY project for those comfortable with basic hand tools. The process requires removing the entire front bumper cover to access the grille's mounting screws from behind.
- Difficulty: 2 out of 5
- Estimated Time: 1.5 hours
- Tools Needed: Flathead screwdriver, Phillips screwdriver, panel clip removal tool, 10mm socket/wrench.
Basic Steps:
- Open the hood and remove the plastic push clips and bolts securing the top of the bumper cover to the radiator support.
- Remove the screws from the front edge of each wheel well that attach the bumper to the fenders.
- Remove the push clips securing the bottom of the bumper cover to the splash shield underneath the car.
- Gently but firmly pull the sides of the bumper cover away from the fenders to release the retaining clips.
- With a helper, pull the entire bumper cover forward and away from the vehicle. Disconnect any fog light wiring if equipped.
- Place the bumper cover on a soft surface (like a blanket) to prevent scratches.
- From the back, remove the screws that hold the old grille and its trim pieces to the bumper cover.
- Install the new grille, transfer the emblem if needed, and reassemble in reverse order.
Technical Specifications & Part Numbers
The grille assembly consists of several components that may be sold separately when new.
| Part Name | Part Number | Description |
|---|---|---|
| Grille Base | 71121-TM8-G01 | The main black plastic structure of the grille. |
| Grille Molding | 71122-TM8-A01ZA | The decorative trim piece in *Light Silver Metallic (NH757M)*. |
| Grille Molding | 71122-TM8-A01ZC | The decorative trim piece in *Medium Silver Metallic (NH766M)*. |
| Front 'H' Emblem | 75701-TF0-003 / 75701-TF0-010 | The Honda emblem. The -010 part number supersedes the -003. |
| Partslink (Aftermarket) | HO1200208 | Refers to the aftermarket grille assembly. |
Frequently Asked Questions
Will a grille from a 2012 Honda Insight fit my 2010 model?
No. The front bumper and grille were redesigned for the 2012 model year. The parts are not interchangeable between the 2010-2011 and 2012-2014 models.
Can I just replace the silver trim piece if it's faded or damaged?
Yes, Honda sells the silver trim moldings separately from the main grille base. You can purchase either the Light Silver (71122-TM8-A01ZA) or Medium Silver (71122-TM8-A01ZC) molding.
Does a new grille come with the Honda emblem?
No, when purchasing new OEM parts, the grille base and the emblem (75701-TF0-003) are sold as separate parts. Used grilles may or may not include the emblem, so it's important to verify with the seller.
How can I tell if I have the Light Silver or Medium Silver trim?
The most reliable way is to check the vehicle information sticker located on the driver's side door jamb. This sticker contains the exterior paint and interior trim codes for your specific car. If the sticker is missing, you may need to compare your grille to online photos or another Insight to determine the correct shade.
Technical Specifications
OEM Part Numbers: 71121-TM8-G01 71122-TM8-A01ZA 71122-TM8-A01ZC 75701-TF0-003 75701-TF0-010
Partslink Number: HO1200208. Trim Color Codes: NH757M (Light Silver Metallic), NH766M (Medium Silver Metallic).
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Honda Insight:
- Symptoms of a Damaged Grille
- Known Issues, Recalls, and TSBs
- Buying a Used 2010-2011 Insight Grille
- 1. Confirm Compatibility: 2010-2011 ONLY
- 2. Inspect All Mounting Tabs
- 3. Check for Hidden Cracks
- 4. Verify the Trim Color
- 5. Emblem and Accessories
- Cost Comparison
- Replacement Overview
- Technical Specifications & Part Numbers
- Frequently Asked Questions
- 🎟️ Get 5% Off