2020-2022 Genesis G90 Grab Handle: Color Matching and Replacement Guide
This guide covers common failure points, what to look for in a used part, and how to replace the interior roof grab handle on your 2020-2022 Genesis G90.
- The most critical factor when buying a replacement is perfectly matching your G90's specific interior color code, as many variations exist.
- Failure is rare and typically involves the slow-retraction mechanism failing or the mounting screws becoming loose.
- Replacement is a very easy DIY task, requiring only basic tools and about 15 minutes per handle.
- There are no recalls or TSBs for this part; issues are from simple wear and tear, making a quality used OEM part a reliable and cost-effective option.
Symptoms of a Failing Grab Handle
Failures of the grab handle on the 2020-2022 Genesis G90 are uncommon and almost always related to physical damage or wear. There are no electronic components to fail. Look for these key symptoms:
- Loose or Rattling Handle: The most common issue is a handle that feels loose in its base or rattles against the headliner. This is typically caused by mounting screws that have backed out over time. While not a failure of the part itself, it requires removal and re-tightening.
- Failed Retraction: The handle may fail to retract, causing it to hang down permanently. Conversely, the damping mechanism can fail, causing the handle to snap back into place with a loud plastic noise instead of retracting smoothly and silently.
- Physical Breakage: In rare cases of extreme force, the handle itself can crack or snap. More likely, the plastic mounting points where the screws pass through can develop cracks, preventing the handle from being secured tightly to the roof.
- Cosmetic Damage: Scratches, scuffs, or discoloration from use or sun exposure are cosmetic issues that can prompt replacement to restore the interior's appearance.
Pro Tip: A rattling noise from the headliner area may not be the grab handle. Before replacing the handle, check the sunroof assembly and headliner clips, as general interior rattles have been noted by some owners.
Buying a Used 2020-2022 G90 Grab Handle
Because this is a simple, durable trim piece, a used OEM handle is an excellent, cost-effective alternative to a new part. However, careful inspection is key to getting a good part that matches your vehicle perfectly.
1. Verify Your Interior Color
This is the most critical step. The 2020-2022 G90 was offered with a wide array of complex, multi-tone interior color schemes. A handle that is the wrong shade of brown, beige, or black will stand out. Do not guess based on photos alone.
Common interior color combinations include:
- Black / Black
- Black / Beige
- Black / Walnut
- Brown / Havana
- Havana / Beige
- Indigo Blue / Dark Brown
Before purchasing, find your vehicle's interior color code on the VIN sticker (usually located on the driver's side door jamb) and provide it to the seller to ensure an exact match.
2. Inspect for Physical Damage
When inspecting the used handle, pay close attention to the following:
- Mounting Points: Check the plastic bases at each end for hairline cracks, especially around the screw holes. This is the most common failure point and can be hard to see.
- Handle Body: Flex the handle slightly and look for any white stress marks in the plastic, which indicate it has been subjected to excessive force.
- Hinge and Spring: Pull the handle down and let it go. It should retract smoothly and slowly. If it snaps back aggressively or hangs loosely, the internal damper or spring is worn out.
3. Check for Position (Front/Rear/Left/Right)
While they may look identical, front and rear handles can have different part numbers and subtle differences in shape or mounting angle. It is best to purchase a handle that is specified for the exact position you are replacing (e.g., "Rear Left").
Known Issues, Recalls, and Service Bulletins
As of mid-2026, there are no recalls or Technical Service Bulletins (TSBs) issued by the NHTSA or Genesis specifically for the roof grab handles on the 2020-2022 Genesis G90. This is expected for a simple, non-critical interior trim component.
Cost Comparison for a G90 Grab Handle
| Part Type | Estimated Cost |
|---|---|
| New OEM | $40 - $70 |
| New Aftermarket | Not Available |
| Used OEM | $15 - $35 |
| Shop Labor | $50 - $100 |
Replacement Guide (Difficulty: 1/5)
Replacing a grab handle is a very simple DIY job that typically takes less than 15 minutes and requires only basic tools.
Tools Required:
- Small flathead screwdriver or plastic trim removal tool
- Phillips head screwdriver or a socket wrench with a 10mm socket (verify screw type)
Step-by-Step Instructions:
- Expose the Mounting Screws: Using a small flathead screwdriver or a trim tool, carefully pry open the small square covers at each end of the grab handle's base. They are hinged and will pop open.
- Remove the Old Handle: Unscrew the two mounting screws that are now visible. Hold onto the handle as you remove the second screw so it doesn't fall.
- Install the New Handle: Position the new handle over the mounting holes in the headliner. Hand-thread both screws to ensure they are aligned correctly.
- Tighten the Screws: Securely tighten both screws. The handle should be snug against the headliner with no movement. Do not overtighten, as this can crack the plastic mounting base.
- Close the Covers: Snap the hinged screw covers shut. Test the handle's operation to confirm it is secure and retracts properly.
Frequently Asked Questions (FAQ)
How do I find the exact color for my G90's interior?
The most reliable way is to find the interior trim code on the vehicle identification sticker located on the driver's side door jamb. This code precisely identifies your colorway (e.g., NNB, NCM) and can be used to confirm a match with a parts seller.
Are the front and rear grab handles interchangeable?
Not always. While they appear very similar, they often have different part numbers for front and rear positions. To guarantee a perfect fit, it is best to buy a handle specifically listed for the position you need to replace.
Can I repair a broken grab handle instead of replacing it?
Repairing a cracked plastic handle or a failed internal spring mechanism is generally not practical or safe. Given the low cost of a used OEM replacement, replacement is the recommended solution.
Do I need any special tools for the replacement?
No, special tools are not required. A small pry tool or flathead screwdriver and a basic screwdriver or socket wrench are all that is needed for this simple 15-minute job.
Helpful Videos
Technical Specifications
OEM Part Numbers: 85343-D2900-NBD (Rear Left, Dark Brown)
Damped, spring-loaded retraction mechanism. Mounts with two screws.
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Genesis G90:
- 🎬 Helpful Videos
- Symptoms of a Failing Grab Handle
- Buying a Used 2020-2022 G90 Grab Handle
- 1. Verify Your Interior Color
- 2. Inspect for Physical Damage
- 3. Check for Position (Front/Rear/Left/Right)
- Known Issues, Recalls, and Service Bulletins
- Cost Comparison for a G90 Grab Handle
- Replacement Guide (Difficulty: 1/5)
- Tools Required:
- Step-by-Step Instructions:
- Frequently Asked Questions (FAQ)
- 🎟️ Get 5% Off