2022-2024 Kia EV6 Glove Drawer: Latch Problems and Replacement Guide

Symptoms of a Failing Glove Box

Problems with the Kia EV6's glove drawer are typically easy to spot and relate directly to the latching and sliding mechanisms.

Glove Drawer Slides Open While Driving

The most common complaint from owners is the glove drawer unexpectedly sliding open. This often happens during acceleration or when driving over bumps. This indicates that the latch is not engaging securely, allowing vibrations or vehicle movement to release it. The contents of the drawer may spill into the passenger footwell, creating a distraction and an annoyance.

Drawer Fails to Latch Shut

You may find the glove drawer will not "click" shut at all. When you push it closed, it simply hits the back and remains loose, or immediately slides back open. This points to a failed or broken component in the latch assembly itself. 🎬 Watch: How to repair a glove box that won't latch An inspection of the plastic hook on the drawer and the catch point in the dashboard can often reveal visible damage.

Known Issues, TSBs, and Recalls

As of late 2024, there are no specific recalls or Technical Service Bulletins (TSBs) from Kia or the NHTSA related to the glove box assembly for the 2022-2024 EV6.

• Common Latch Issue: Despite no official bulletins, owner forums contain reports of the latch failing to hold the drawer closed, suggesting a potential weakness in the latch design.
• Unrelated Major Recalls: The 2022-2024 Kia EV6 has been subject to several significant recalls, most notably for the Integrated Charging Control Unit (ICCU), which could lead to a loss of driving power. These recalls are unrelated to the vehicle's interior components like the glove box.

Buying a Used 2022-2024 EV6 Glove Box: What to Inspect

A used OEM glove drawer is an excellent, cost-effective solution, as aftermarket options are generally not available. Because fit and color are critical, a recycled original part is superior to a non-existent cheap alternative. Pay close attention to the following before buying.

1. Verify the Part Number and Color

This is the most critical step. The EV6 was offered with different interior color schemes, and the glove box must match. The last few letters of the part number indicate the color. The two most common part numbers are:

• 84511-CV100CVH
• 84511-CV100WK

Always confirm the part number from the seller matches the one you need. If you are unsure, it is best to have a Kia dealer look up the correct part number for your specific VIN.

2. Inspect the Latch Mechanism

Carefully examine the plastic latching hook on the top of the drawer assembly. Look for stress marks (whitish lines in the plastic), cracks, or evidence that it has broken off. This is the most likely failure point. Also, check the corresponding striker area inside the dashboard cavity on your own vehicle to ensure it is not damaged.

3. Test the Sliding Mechanism

Ask the seller to confirm that the drawer slides smoothly on its tracks. The rails and any rollers should be intact and free of damage. A drawer that is difficult to move or feels gritty may have damaged slides, which are integral to the assembly.

4. Check for Cosmetic and Structural Damage

Inspect all photos for deep scratches, cracks on the face of the drawer, or broken mounting tabs. Mounting points are essential for a secure, rattle-free installation.

Replacement Difficulty and Guide

Replacing the glove drawer assembly is a straightforward DIY job that requires only basic tools.

• Difficulty: 1 out of 5
• Time to Replace: 15-30 minutes
• Tools Needed: Phillips head screwdriver, possibly a small trim removal tool.

Step-by-Step Replacement (General Process)

1. Empty the Glove Box: Remove all contents from the drawer.
2. Locate Mounting Screws: The assembly is typically held in by several Phillips head screws. These may be located along the top and bottom edges of the glove box opening inside the dashboard. You may need to slide the drawer partially out to access them.
3. Disconnect Electrical Connector: The glove box has an interior light. Before fully removing the assembly, reach behind it and disconnect the small wiring harness that powers the light. There will be a small tab on the connector to press for release.
4. Remove the Old Assembly: With the screws removed and the light unplugged, the entire drawer assembly should slide out of the dashboard.
5. Install the New Assembly: Slide the replacement glove box into the cavity. Reconnect the electrical connector for the light, then align the mounting holes and reinstall the screws. Do not overtighten them.
🎬 See this step-by-step cabin filter and glove box removal guide
6. Test for Function: Push the drawer closed to ensure it latches securely. Press the release button to confirm it opens correctly.

Cost Comparison for a 2022-2024 EV6 Glove Box

Frequently Asked Questions (FAQ)