2016-2021 Toyota Land Cruiser Fender: Fitment, Part Numbers, and Replacement
Your definitive guide to identifying, sourcing, and replacing a fender on the facelifted 200-Series Land Cruiser, ensuring a perfect fit and finish.
- Only fenders specifically for the 2016-2021 Land Cruiser will fit due to the major body style update in 2016.
- Fenders from the Lexus LX 570 are NOT interchangeable despite sharing a platform.
- Used OEM fenders offer the best fit, but inspect them carefully for hidden body filler and verify they have the correct mounting holes for your vehicle's side molding.
- New fenders, whether OEM or aftermarket, come unpainted and require professional painting, which can be a significant portion of the total cost.
Symptoms of a Damaged Fender
Unlike mechanical parts, fender failure is almost always the result of physical damage. Because they are located at the corners of the vehicle, they are highly susceptible to impacts. You'll know a fender needs replacement when you see:
- Visible Dents and Creases: Minor dents from parking lot bumps or shopping carts can often be repaired by a paintless dent removal (PDR) specialist. However, large dents or sharp creases that have stretched the metal will likely require the fender to be replaced.
- Cracks or Tears: A significant collision can tear or crack the fender's metal. This type of damage compromises the panel's structural integrity and cannot be safely repaired; replacement is the only option.
- Severe Corrosion or Rust: While the 200-series Land Cruiser has excellent corrosion resistance, deep scratches or rock chips that expose the bare metal can lead to rust over time. Surface rust can be sanded and repaired, but rust that has eaten through the panel requires replacement.
- Poor Panel Gaps: If the gaps between your fender and the hood, door, or bumper are uneven, it can indicate a bent fender or underlying structural damage from a previous accident.
Buying a Used Fender for a 2016-2021 Land Cruiser
For a vehicle like the Land Cruiser, a high-quality used OEM fender is often a better choice than a new aftermarket part. Original Toyota fenders are manufactured with higher quality steel and are designed to fit perfectly, ensuring even panel gaps and proper alignment. Aftermarket fenders can be made from thinner metal and often require extra work during installation to achieve an acceptable fit.
Inspection Checklist for a Used Fender:
- Check for Hidden Repairs: Run a small magnet along the entire surface of the fender. If the magnet fails to stick in certain areas, it indicates the presence of body filler (Bondo), signaling a previous repair. A thin layer of filler for a minor dent may be acceptable, but thick filler can crack and fall out over time.
- Inspect All Mounting Points: Carefully examine every mounting tab and hole. Look for any signs of stress cracks, bends, or elongated holes. Damaged mounting points will make it impossible to install and align the fender correctly.
- Look for Kinks and Bends: Lay the fender on a flat surface and look down its length. Check for subtle waves or bends in the metal that might not be obvious at first glance. These can be signs of a poorly repaired fender.
- Verify Side Molding Holes: The initial buyer warnings are correct. Some Land Cruiser trim levels have side protection molding, while others do not. Inspect the used fender to ensure it has the correct mounting holes—or lack thereof—to match your vehicle's specific trim.
- Assess Paint Condition: Finding a used fender in your vehicle's original color can save you hundreds of dollars in paint costs. Check for deep scratches, clear coat peeling, or significant fading. Even with a color-matched part, professional blending into the adjacent door and bumper may be necessary for a perfect match.
Pro Tip: Used fenders for this specific generation of Land Cruiser can be difficult to find due to the vehicle's relatively high value and robust build. If you find a clean, damage-free used OEM fender, it is a valuable part.
Known Issues, TSBs, and Recalls
As of mid-2026, there are no specific recalls, Technical Service Bulletins (TSBs), or common factory defects related to the fenders on the 2016-2021 Toyota Land Cruiser. The recalls issued for this vehicle generation pertain to components like the fuel pump, airbags, and load capacity labels. The absence of fender-related issues speaks to the high manufacturing quality of the vehicle's body panels.
Fender Replacement Overview
Replacing a front fender on a 2016-2021 Land Cruiser is a moderately difficult job that a skilled DIYer can perform. The key challenge is achieving perfect alignment upon reinstallation.
General Steps Include:
- Remove the Front Wheel: This provides access to the fender liner.
- Remove the Fender Liner: The plastic liner is held in by a series of clips and screws.
- Remove the Front Bumper Cover: The bumper must be at least partially removed to access the bolts connecting it to the fender.
- Unbolt the Fender: The fender is secured by bolts along the top under the hood, one inside the door jamb (door must be open to access), and at the front and bottom.
- Mark Alignment Points: Before fully removing the old fender, use a marker to trace the position of the bolts/washers under the hood. This will serve as a crucial reference point for aligning the new fender.
- Install New Fender: Loosely attach the new fender. Align it with your marks and ensure even gaps with the door, hood, and bumper before tightening the bolts.
Warning: Some forum users note that one or two rivets may need to be drilled out near the headlight assembly to fully remove the fender. These will need to be replaced with new rivets during installation.
Cost Comparison for a Single Fender
Prices can vary based on location and supplier. The costs below are estimates as of late 2024 and do not include painting unless specified.
| Part Type | Estimated Cost | Notes |
|---|---|---|
| New OEM | $270 - $405 | Purchased from an online dealer parts department or directly from a local dealership. Comes unpainted. |
| New Aftermarket | $215 - $280 | Brands like CAPA-certified or standard replacements. Fit may not be as precise as OEM. Comes primed. |
| Used OEM | $150 - $300 | Availability is often low. Price depends heavily on condition and whether it matches your paint code. |
| Shop Labor (Installation) | $250 - $480 | Based on 2.5-3.0 hours of labor at a rate of $100-$160/hour. This does NOT include painting. |
| Shop Labor (Paint) | $400 - $900 | Includes prep, primer, a multi-stage color coat, clear coat, and blending into adjacent panels for a perfect match. |
Technical Specifications and Part Numbers
These are the primary part numbers for the 2016-2021 model years. Always confirm with your VIN before ordering.
- Right / Passenger Side Fender: 53801-60D50 (Toyota), TO1241264 (Partslink)
- Left / Driver Side Fender: 53802-60D60 (Toyota), TO1240264 (Partslink)
- Note on Side Molding: Some part diagrams include a note: "W(SIDE PROTECTION MOULDING)". This confirms that variations exist. Double-check that the part you order matches your vehicle's trim package.
Frequently Asked Questions
Will a fender from a 2016-2021 Lexus LX 570 fit my Land Cruiser?
No, they will not interchange. While the Land Cruiser and LX 570 share the same basic chassis, their exterior body panels, including the fenders, are different to accommodate unique headlight designs and body lines. The OEM part numbers are different, confirming they are not the same part.
How do I find my Land Cruiser's paint code?
Your vehicle's paint code is on the manufacturer's sticker located inside the driver's side door jamb. Look for the letters "C/TR" followed by a three-character code. This is your exterior color code, which is essential for ordering a painted part or for a body shop to match the paint.
Do I have to paint a new fender?
Yes. Both new OEM and new aftermarket fenders are shipped unpainted or with only a black protective primer. This primer must be sanded off, and the new fender must be properly prepped, primed, color-matched, and clear-coated to match your vehicle and protect the metal from rust.
Is it better to repair or replace my damaged fender?
If the damage is limited to minor dents or surface scratches, repair is usually more cost-effective. However, if the metal is torn, severely creased, or has extensive rust, replacement is the only safe and correct option. A professional body shop can assess the damage and provide the best recommendation.
Technical Specifications
OEM Part Numbers: 53801-60D50 5380160D50 53802-60D60 5380260D60
Material: Steel. Finish: Unpainted E-Coat or Primer.
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Toyota Land Cruiser: