2022-2025 Lucid Air Overhead Console: Decoding Part Numbers and Common Glitches

Critical Compatibility Warning: Match Your Part Number

Symptoms of a Failing Overhead Console

Failures in the Lucid Air's overhead console are more often related to software glitches than physical hardware breakdown. Given the vehicle's complex, screen-based architecture, many issues that seem like a broken part are actually temporary software freezes.

• Unresponsive Buttons: The most common symptom is when the physical buttons for the dome lights, hazard lights, or sunshade do not respond to presses. This can be intermittent or a permanent failure.
• Intermittent Operation or Freezing: Many Lucid owners report instances where all interior controls, including the main touchscreens and steering wheel buttons, become unresponsive mid-drive. If this occurs, the overhead console will also likely stop working. This is typically a software issue that can be resolved with a system reboot.
• SOS System Malfunction Warning: If the console has a fault, it may trigger a warning message related to the SOS or emergency call system.
• Lights Stuck On or Off: A hardware failure within the switch panel could cause the interior dome or map lights to remain on, potentially draining the 12-volt battery, or prevent them from turning on at all.

Known Issues, Recalls, and Technical Service Bulletins (TSBs)

As of mid-2024, there are no specific recalls or TSBs issued by Lucid or the NHTSA for the overhead control console switch panel itself.

However, the 2022-2025 Lucid Air has been subject to several recalls for related electronic systems, which highlights a pattern of potential software and wiring issues in early production vehicles:

• NHTSA Recall 26V017 / 25V670: These software-related recalls address issues where the rearview camera image may not display, may lag, or may go blank. While not directly related to the overhead console, they underscore the prevalence of software bugs that are typically fixed with an Over-The-Air (OTA) update.
• Display Wiring Harness Recall: An earlier recall was issued for a wiring harness for the main driver displays that could chafe against the steering shaft, potentially causing the screens to go blank. This indicates that wiring and harness routing issues can be a source of electrical problems in the vehicle.

Buying a Used 2022-2025 Lucid Air Overhead Console

Due to the vehicle's newness, new aftermarket or remanufactured options for this part do not exist. A used OEM console is the most practical and cost-effective solution outside of purchasing a new part from a Lucid service center.

What to Check Before You Buy:

1. Verify the Part Number: This is the most critical step. As mentioned, part numbers like P11-NBA1AS-05 and P11-NBA1AS-04 exist. You must match the number on your old part exactly to ensure compatibility with your car's roof and other features.
2. Physical Inspection: When inspecting photos or the part in person, look for:
   • Intact Mounting Clips: The console is held in by several plastic clips. Ensure none are broken or cracked, as this will prevent it from seating securely in the headliner.
   • Connector Pins: Check the electrical connector port for any bent, corroded, or broken pins.
   • Button and Lens Condition: Make sure the button graphics aren't worn off and the plastic lenses for the lights are not cracked or heavily scratched.
3. Source Vehicle Information: If possible, get the VIN of the vehicle the part came from. This can sometimes help a Lucid service center verify compatibility if you are unsure.

Cost Comparison

Pricing for this part can vary, but this provides a general expectation of costs.

Replacement Information

Replacing the overhead console is generally straightforward and can be performed by a DIYer with basic tools and patience.

• Difficulty: 2 out of 5
• Estimated Time: 0.5 hours
• Tools Required: Plastic trim removal tool kit.

Step-by-Step Replacement Guide (General Procedure)

While no specific Lucid Air guide exists, the process is similar to most modern vehicles.

1. Get a Grip: Start at the edge of the console closest to the windshield or the rear. Use a plastic pry tool to gently create a small gap between the console and the headliner.
2. Release the Clips: Work your fingers or the pry tool around the edge of the console, applying firm, steady downward pressure. You will hear loud popping or cracking sounds as the metal retaining clips release; this is normal and does not mean the part is breaking.
3. Lower the Console: Once all clips are free, carefully lower the console. Do not pull it all the way down, as it is still connected by one or more electrical harnesses.
4. Disconnect the Harness: Locate the electrical connector(s) on the back of the console. Press the release tab on the connector and pull it straight out to disconnect it.
5. Installation: To install the new console, simply reconnect the electrical harness, align the console with the opening in the headliner, and press firmly upwards until all the clips snap securely into place. Test all buttons to confirm proper function.

Frequently Asked Questions (FAQ)