2022-2026 Genesis G70 Rear Bumper Corner Trim: A Guide to Part Numbers and Replacement
This guide covers the essential details for replacing the rear bumper corner filler panels on your 2022-2026 Genesis G70, including correct part numbers and what to inspect on a used part.
- You must remove the entire rear bumper cover to properly replace this part; it does not simply pop on and off.
- Verify the correct side before ordering: 86694-G9500 is for the Left (Driver) side and 86695-G9500 is for the Right (Passenger) side.
- When buying a used part, the condition of the mounting tabs on the back is more important than minor surface scuffs.
- There are no specific recalls or TSBs for this part, and aftermarket options are generally not available.
Symptoms of a Failing Bumper Filler Panel
Failure of this part is always visual and typically caused by physical impact. There are no mechanical or electrical symptoms associated with this simple trim piece.
- Visible Damage: The most common symptom is damage from a minor collision, such as cracks, deep scuffs, or a completely broken panel.
- Poor Fitment or Gaps: The panel may pop out of place or show a noticeable gap between it and the bumper or body. This is often due to broken mounting clips or tabs, a known weak point on G70 bumpers. You might be able to push it back into place, but it will likely pop out again if the underlying tabs are damaged.
- Missing Piece: In some cases, a minor impact can be enough to break the panel or its clips entirely, causing it to fall off the vehicle while driving.
- Discoloration or Fading: Over time, the plastic may fade or become discolored due to sun exposure, though this is less common on newer vehicles.
Pro Tip: Forum users have noted that G70 bumper clips and tabs can be fragile. If your corner trim is popping out without any obvious impact, it's likely one or more mounting tabs have failed. An aftermarket bumper guide repair kit exists for the front bumper, highlighting how common this issue is for the model in general.
Buying a Used Bumper Filler Panel
Since this is a cosmetic part, buying a used OEM panel is a great way to save money. Aftermarket versions of this specific corner trim are not commonly available, making used OEM the best alternative to a new dealer part. When inspecting a used panel, focus on its structural integrity, not just its surface.
Key Inspection Points:
- Check All Mounting Tabs: This is the most critical inspection point. Carefully examine the back of the panel and ensure every mounting tab and clip receiver is intact and free of stress marks or cracks. A panel with even one broken tab will not sit flush and may pop out easily.
- Look for Hidden Cracks: Flex the panel slightly to reveal any hairline cracks that may not be visible at first glance. Pay close attention to the areas around the mounting points.
- Verify the Side: Before purchasing, double-check that you are buying the correct side for your vehicle. The part numbers are side-specific. See the table below for details.
- Assess Cosmetic Condition: Look for deep scratches or gouges. Minor scuffs can often be polished out, but deep damage will require repainting, adding to the cost. Since these parts come unpainted from the factory, finding one in your car's color is a bonus but not guaranteed.
Known Issues, TSBs, and Recalls
As of mid-2024, there are no specific recalls or Technical Service Bulletins (TSBs) from the National Highway Traffic Safety Administration (NHTSA) for the rear bumper corner filler panels on the 2022-2026 Genesis G70. While other recalls exist for the G70, none pertain to this cosmetic trim piece.
Replacement and Installation
Replacing this corner trim piece is more involved than it may appear. It is not a simple pop-out, pop-in part. To access its mounting points, the entire rear bumper cover assembly must be removed from the vehicle.
A YouTube video provides a detailed walkthrough of the rear bumper removal process on a 2022 G70. The general steps include:
- Opening the trunk and removing interior trim panels to access the tail light and bumper reinforcement bolts.
- Removing the tail lights to expose hidden screws and clips.
- Removing multiple screws and push-clips from inside both rear wheel wells.
- Removing all clips and screws along the bottom edge of the bumper cover.
- Carefully unsnapping the bumper cover from the mounting brackets on each side, starting at the wheel wells.
- Disconnecting any parking sensor harnesses before fully removing the bumper.
- Once the bumper cover is off the car, the corner trim pieces can be unclipped and replaced from the inside.
Due to the number of steps and the risk of breaking fragile plastic clips, this job requires patience and care.
Warning: Be extremely careful when prying clips and pulling the bumper cover away from the body. The plastic tabs that hold the bumper in place are known to be fragile and can break easily.
Cost Comparison
The following prices are estimates and can vary based on supplier and location. These parts are typically sold unpainted (primed black).
| Part Type | Estimated Cost |
|---|---|
| New OEM | $30 - $45 |
| New Aftermarket | Not Available |
| Used OEM | $15 - $30 |
| Shop Labor (Installation) | $150 - $375 |
Technical Specifications & Part Numbers
It is critical to order the correct part for the side you need to replace. The part numbers are different for the driver and passenger sides.
| Side | Common Name | Part Number |
|---|---|---|
| Left (Driver Side) | Corner Trim, Left | 86694-G9500 |
| Right (Passenger Side) | Corner Trim, Right | 86695-G9500 |
Frequently Asked Questions (FAQ)
Do I need to paint a new bumper filler panel?
Yes. New OEM bumper filler panels are typically sold in a black, unpainted, primed finish. You will need to have the part professionally painted to match your vehicle's body color.
Can I replace just the corner piece without removing the whole bumper?
No, it is not recommended. The corner trim is secured by clips and tabs from inside the bumper cover. To replace it correctly and ensure a secure fit, you must remove the entire rear bumper assembly from the car.
Why is my bumper corner trim popping out?
This is usually caused by broken mounting tabs on the back of the trim piece or on the bumper bracket it attaches to. This can happen from a very minor impact or even from removing the bumper improperly during a previous repair.
Is there a difference in this part between G70 trim levels (e.g., 2.5T vs 3.3T Sport)?
No, the OEM parts diagrams indicate that this specific corner trim piece is the same across all 2.5T and 3.3T trim levels for the 2022-2026 model years. However, it is always best to verify fitment with your vehicle's VIN when ordering.
Technical Specifications
OEM Part Numbers: 86694-G9500 86695-G9500
Material: Plastic. Finish: Unpainted/Primed.
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Genesis G70: