2019-2023 Jaguar I-Pace Rear Bumper Absorber: Inspection, Cost, and Replacement
Your guide to ensuring safety and proper fitment when replacing the rear impact absorber on your Jaguar I-Pace.
- The rear bumper absorber is a one-time-use safety part and must be replaced after any rear impact, no matter how minor.
- Part number T4K5313 fits all 2019-2023 Jaguar I-Pace models.
- There are no aftermarket options, making a carefully inspected used OEM part a strong value.
- Replacement requires the complete removal of the rear bumper cover, a job rated 3/5 in difficulty.
What are the Symptoms of a Damaged Rear Bumper Absorber?
As a passive safety part, a bumper absorber doesn't have electrical or mechanical failures in the traditional sense. Its failure is purely physical damage resulting from an impact. The symptoms are often hidden until the bumper is inspected closely.
- Loose or Misaligned Bumper Cover: After a minor rear-end bump, you might notice the bumper cover is no longer flush with the body panels. This can happen if the absorber underneath has been crushed or if its mounting points have broken, preventing the cover from seating correctly.
- Visible Cracks or Compression: The most definitive symptom is visible damage to the absorber itself. This is usually only apparent once the rear bumper cover is removed. The foam will appear compressed, cracked, or may have pieces broken off. Any visible damage means the part has done its job and must be replaced.
Warning: A bumper absorber is a one-time-use part. Even if it appears only slightly compressed after a minor collision, its ability to absorb energy in a future impact is significantly compromised. It should always be replaced after any impact, no matter how small.
Buying a Used 2019-2023 I-Pace Rear Bumper Absorber
Since no aftermarket versions of this part are commonly available, a quality used OEM absorber is an excellent value. However, careful inspection is critical to ensure you are buying a part that will perform correctly. A damaged used absorber offers no safety benefit.
Inspection Checklist for a Used Absorber:
- Check for Compression: Look at the part from all angles. The foam should be uniform in shape and thickness. Look for any areas that appear flattened, squashed, or indented. Compare it to photos of a new part if you are unsure.
- Inspect for Cracks and Stress Marks: Examine the entire surface, especially around corners and mounting areas, for cracks. On the black foam, look for fine white lines, which indicate the material has been stressed to its breaking point. Any cracks or stress marks are a red flag.
- Verify All Mounting Points: The absorber attaches to the bumper reinforcement bar with a series of clips or tabs molded into the foam. Ensure every single one of these is present and intact. A broken tab can cause rattles or prevent the part from staying securely in place.
- Confirm the Part Number: Verify that the part is OEM number T4K5313. While this part fits a wide range of years (2019-2023), confirming the number ensures you have the exact correct piece.
Known Issues, Recalls, and Technical Service Bulletins (TSBs)
As of mid-2024, there are no NHTSA recalls or manufacturer TSBs specifically related to the rear bumper absorber on the 2019-2023 Jaguar I-Pace. This indicates there are no known widespread defects or premature failures with the original factory part outside of damage from collisions.
Replacement Overview and Difficulty
Replacing the rear bumper absorber requires removing the rear bumper cover first. While this does not require specialized tools, it does demand patience and care to avoid damaging the paint or plastic clips.
Pro Tip: Have a soft blanket or large piece of cardboard ready to place the bumper cover on once it's removed. This will prevent scratches to the paint.
Step-by-Step Overview:
- Disconnect Sensors: If your vehicle has parking sensors, open the trunk and locate the wiring harness for the rear bumper. Disconnect it before proceeding.
- Remove Fasteners: Remove all screws and plastic clips holding the bumper cover in place. These are typically located in the rear wheel wells, underneath the bumper, and along the top edge inside the trunk/hatch opening.
- Release the Cover: Gently but firmly pull the sides of the bumper cover away from the vehicle to release them from the mounting brackets under the taillights. It can be helpful to have a second person for this step.
- Swap the Absorber: With the bumper cover removed, the foam absorber will be visible, attached to the metal bumper bar. It is usually held on by simple clips. Unclip the old, damaged absorber and clip the new one into place.
- Reinstall: Reinstall the bumper cover by reversing the removal steps. Be sure to reconnect the sensor wiring harness before fully seating the bumper.
Cost Comparison: New vs. Used
Because there are no aftermarket options, your choice is between a new OEM part from a dealer or a used OEM part from a recycler.
| Part Type | Estimated Cost |
|---|---|
| New OEM | $150 - $200 |
| New Aftermarket | Not Available |
| Used OEM | $75 - $125 |
| Shop Labor | $150 - $375 |
Frequently Asked Questions (FAQ)
Can I reuse my bumper absorber after a small bump?
No. The foam is designed to crush and absorb energy only once. Even a small amount of compression permanently weakens it, and it will not provide the designed level of protection in a subsequent impact. It must be replaced.
Is the bumper absorber the same as the bumper reinforcement bar?
No. The bumper absorber is the block of foam. The bumper reinforcement bar (or bumper beam) is the strong metal bar located behind the absorber. The absorber protects the bar from damage in low-speed impacts.
Does replacing the absorber require any computer programming?
No. The absorber itself is a non-electronic part. However, you must remember to disconnect and reconnect the wiring for the parking sensors located in the bumper cover. Failure to do so can damage the wiring or trigger warning lights, but it does not require reprogramming.
Why do I need to verify my VIN if this part fits 2019-2023 models?
While part number T4K5313 fits all 2019-2023 I-Pace models, verifying the VIN with a parts supplier is always a good practice. It helps guarantee that no mid-year production changes or specific trim package differences affect the part you are ordering, ensuring a perfect fit without delays.
Technical Specifications
OEM Part Numbers: T4K5313
Material: Expanded Polypropylene (EPP) Foam
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Jaguar I-Pace:
- What are the Symptoms of a Damaged Rear Bumper Absorber?
- Buying a Used 2019-2023 I-Pace Rear Bumper Absorber
- Inspection Checklist for a Used Absorber:
- Known Issues, Recalls, and Technical Service Bulletins (TSBs)
- Replacement Overview and Difficulty
- Step-by-Step Overview:
- Cost Comparison: New vs. Used
- Frequently Asked Questions (FAQ)
- 🎟️ Get 5% Off