2017-2019 Karma Revero B-Pillar Trim: A Buyer's Guide to 'Palisades Sport' Panels

Critical Compatibility Warning: 2017-2019 vs. 2020+ Models

Symptoms of Failing B-Pillar Trim

Failure of a B-pillar trim panel is almost always related to physical wear or damage, not a mechanical fault. Symptoms are typically minor but can be annoying in a luxury vehicle.

• Rattling or Buzzing Noises: This is the most common symptom, often caused by broken or loose plastic mounting clips on the back of the panel. The noise may be most noticeable when driving over rough roads.
• Visible Cosmetic Damage: Scratches, scuffs, and gouges are common, especially on the lower panel from contact with feet or seatbelts.
• Peeling or Delamination: The surface material, whether leather or a soft-touch coating, can begin to peel, bubble, or separate from the plastic base, particularly with age and sun exposure.
• Poor Fitment: The panel may have visible gaps where it meets the headliner or other trim pieces, often as a result of broken clips or improper installation.

Buying a Used 2017-2019 Karma Revero B-Pillar Trim Panel

Due to the rarity of the Revero, new aftermarket panels are nonexistent, and new OEM parts can be exceptionally expensive and require special orders. A used OEM panel from a reputable recycler is the most practical and cost-effective solution. Pay close attention to the following details before buying.

1. Confirm Your 'Palisades Sport' Interior Package

This is the most critical step. The part numbers listed are specifically for vehicles with the 'Palisades Sport' interior trim package. While other panels may physically fit, the colors and materials will not match. Based on available information, the Palisades interior features a distinct two-tone color scheme, often in black and red, with carbon fiber trim accents. Before purchasing, compare photos of the seller's part to your vehicle's interior to ensure an exact match of color, material texture, and sheen.

2. Inspect All Mounting Points

Ask the seller for clear, high-resolution photos of the back of the panel. Carefully check that all plastic mounting clips and tabs are present and intact. These clips are brittle and often break during removal. A panel with even one broken clip may not sit flush and can cause persistent buzzing or rattling noises.

3. Examine for Physical and Sun Damage

• Surface Condition: Look for deep scratches, cracks, or stress marks in the plastic structure.
• Color Fading: Compare the color to areas of your interior that are not exposed to sunlight. Ensure the panel is not faded or discolored from UV exposure.
• Material Integrity: For leather or soft-touch surfaces, check for any signs of peeling, bubbling, or stains.

Cost Comparison for Revero B-Pillar Trim Panels

Pricing can vary based on condition and availability. As these are low-volume parts, expect higher-than-average costs compared to a mass-market vehicle.

Known Issues, TSBs, and Recalls

As of mid-2026, there are no specific recalls or Technical Service Bulletins (TSBs) for the B-pillar interior trim panels on the 2017-2019 Karma Revero.

However, a significant safety recall is relevant to this area of the vehicle:

• NHTSA Recall 19V-296 (Airbag Rollover Sensors): This recall was issued for 231 examples of the 2018 Revero because the rollover sensors for the side-curtain airbags were not enabled from the factory. Servicing this issue could potentially require the removal of B-pillar trim panels to access components. It is crucial to verify with a dealer or through the NHTSA website that this recall has been completed on any 2018 Revero.

A TSB was also issued for the front door glass not sitting flush against the B-pillar location, which required adjustments. While not a fault of the trim itself, it shows the importance of proper panel fitment in this area.

Replacement Difficulty and Procedure

• Difficulty: 1 out of 5 (Easy)
• Estimated Time: 0.5 hours
• Tools Required: Plastic trim removal tool set.

Replacing an interior B-pillar trim panel is generally a straightforward DIY task. The panels are held in place by hidden metal spring clips and plastic alignment tabs.

1. Prepare the Area: If replacing the lower panel, move the front seat forward for better access.
2. Remove Upper Trim (if necessary): The upper and lower B-pillar panels often overlap. You may need to partially or fully remove the upper panel to access the lower one.
3. Pry Off the Panel: Insert a plastic trim removal tool into the seam between the panel and the vehicle body or adjacent trim. Gently pry to release the first clip. Work your way around the panel, releasing each clip until the panel comes loose. Do not use a metal screwdriver, as it will damage the panel and the vehicle's body.
4. Manage the Seatbelt: The panel is typically designed with a slot to be removed from around the seatbelt. You do not usually need to unbolt the seatbelt anchor.
5. Install the New Panel: Align the clips on the new panel with the corresponding holes in the B-pillar. Position it correctly around the seatbelt. Give the panel a firm tap with the palm of your hand over each clip location to snap it securely into place. You should hear an audible click as each clip engages.

OEM Part Numbers

These part numbers are known to be associated with the upper and lower B-pillar trim panels for the 2017-2019 Karma Revero with the 'Palisades Sport' interior. Always verify the part number from your original part if possible before ordering a replacement.

Note: Part numbers for left and right sides are often distinguished by the final digits (e.g., an odd vs. even number), but this is not always consistent. Visual confirmation is the best method.

Frequently Asked Questions (FAQ)